MGD8100DC1 Maytag Dryer - Overview
Sections of the MGD8100DC1
[Viewing 7 of 7]
Keep searches simple, eg. "belt" or "pump".
Dryer Idler Pulley
PartSelect #: PS334244
Manufacturer #: 279640
This Idler Pulley includes the tri-ring and gasket and everything included here is manufacturer-certified. This part maintains correct tension on the drive belt in order to spin the drum properly. If ...
$25.95
In Stock
Dryer Drum Support Roller
PartSelect #: PS11752609
Manufacturer #: WPW10314173
This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. This part is sold separ...
$18.88
In Stock
Dryer Igniter Kit
PartSelect #: PS334180
Manufacturer #: 279311
If your dryer will not heat, takes too long to dry, or does not provide enough heat, you might want to replace your igniter kit. This silicone carbide igniter with ceramic holder kit includes the 3-in...
$35.67
In Stock
Dryer Thermostat Internal bias
PartSelect #: PS11746740
Manufacturer #: WP8577274
The internal-bias thermistor (Thermistor, Dryer Thermister, Dryer Thermistor) prevents the dryer from overheating by monitoring and controlling the temperature of the inside of the dryer drum. It is l...
$35.67
In Stock
Dryer Tri Ring
PartSelect #: PS11755850
Manufacturer #: WPW10512946
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
$10.95
In Stock
Dryer Radiant Flame Sensor
PartSelect #: PS11741429
Manufacturer #: WP338906
If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor if it is hot enough ...
$34.95
In Stock
Washer Leveling Foot
PartSelect #: PS1609293
Manufacturer #: 49621
If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs, adjust the legs so...
$7.29
In Stock
Idler Pulley w/Bracket
PartSelect #: PS11726337
Manufacturer #: W10837240
The idler pulley with bracket ensures proper tension on the dryer’s drive belt, allowing the drum to spin effectively. This assembly includes the pulley and arm, making it ideal for replacing a worn o...
$27.24
In Stock
Dryer Electrode Sensor
PartSelect #: PS11741408
Manufacturer #: WP3387223
This is the moisture sensor for your dryer. It helps detect the amount of moisture in your clothes during the dryer cycle. If you notice your clothes are still wet after an automatic dryer cycle is do...
$9.95
In Stock
Dryer Screw
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$7.95
In Stock
Drum Seal w/Adhesive
PartSelect #: PS970088
Manufacturer #: 280114
This drum seal with a silicone rubber adhesive is used in dryers. This part seals the drum to make sure air does not escape from the dryer. If your dryer is making loud noises, is not producing enough...
$42.95
In Stock
Hinge
PartSelect #: PS11750410
Manufacturer #: WPW10208415
This is a door hinge, which allows for your washer door to properly shut during the washing cycle, and open after it is finished. If your door hinge is bent or broken and not allowing the door to shut...
$80.42
In Stock
Questions And Answers for MGD8100DC1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the MGD8100DC1
[Viewing 11 of 11]Noisy
Fixed by
these parts
these parts
Show All
Not Heating
Fixed by
these parts
these parts
Show All
Too hot
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Won’t Start
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Door Sags
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Very Loud Squeaking Noise
1) Disconnected power cord from wall. 2) Disconnected vent hose from back of dryer. 3)Removed dryer rear panel. 4)Disengaged tension spring on idle wheel arm. 5) Removed worn idle wheel. 6)Installed new Idler wheel assembly. 7) Vacuumed dust from rear of dryer (optional, recommended). 8) Reinstalled rear cover, vent hose and power cord. E
... Read more
asy repair 15-30
Read less
Parts Used:
-
GREGORY from Wilsonville, OR
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
75 of 96 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No heat to dry clothes
First I took the front of the dryer off then located the igniter. It only required removing two screws, removing old igniter, replacing with new igniter, and replacing the two screws.. While I was replacing the igniter I took the drum out and throughly cleaned the inside. Lucky me, I found 85 cents on the floor of the dryer. I am 65yr
... Read more
s old, married and mother of two.
This was easy to do and sure saved money. I reccommend others try to do repairs for themselves and using PartSelect was less expensive too.
This was easy to do and sure saved money. I reccommend others try to do repairs for themselves and using PartSelect was less expensive too.
Read less
Parts Used:
-
Karen from Pine Mtn. Club,, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
66 of 76 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rear tub seal failure
I removed the top cover and then the back cover, released the belt tensioner and removed the drive belt. Then slid the tub out of the unit and onto the back dack. Sanded the remnents of the old seal off. Wiped the tub lip with laquer thinner and applied the "fast" drying glue supplied with the kit. Installed the seal and re-assembled the
... Read more
unit...works fine
Read less
Parts Used:
-
Jerry from Everett, WA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
66 of 86 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!