MGT8720DH06 Maytag Range - Overview
Sections of the MGT8720DH06
[Viewing 9 of 9]
Keep searches simple, eg. "belt" or "pump".
Refrigerator Light Bulb (40w)
PartSelect #: PS884734
Manufacturer #: 8009
This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
$17.80
In Stock
Leveler Foot Screw (Nylon)
PartSelect #: PS16875974
Manufacturer #: W11665456
This is a leveling leg for your oven, range, or stove. The leveling legs on your oven allow your appliance to sit perfectly flat. The new one may be longer in length than your original, but will work...
$21.95
In Stock
Range Rack
PartSelect #: PS11749669
Manufacturer #: WPW10179152
This oven rack is chrome in color and is approximately 24.76 inches wide by 15.78 inches deep. If your old oven rack is damaged, you should consider replacing it. Many of our customers have determined...
$81.45
In Stock
Refrigerator Screw
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$20.95
In Stock
Dryer Screw
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$7.95
In Stock
IGNTR-OVEN
PartSelect #: PS16744717
Manufacturer #: W11596211
This bake or broil igniter ignites the gas for the oven burner by glowing white. If any of the following symptoms occur, it is best to replace this part: little to no heat when baking, oven will not t...
$62.32
In Stock
Dryer Screw 1016 X 1
PartSelect #: PS11741409
Manufacturer #: WP3387230
This screw is sold individually.
$8.37
In Stock
Refrigerator Touchup Paint (White)
PartSelect #: PS385132
Manufacturer #: 72017
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$12.58
In Stock
2 Piece Broiler Pan
PartSelect #: PS971245
Manufacturer #: 4396923
This is cookware designed for use in your range or oven. It is a two-piece dish that is used to grill or cook food while the broil function is on, meaning it can withstand high temperatures. This set ...
$47.20
In Stock
SOCKT-LITE
PartSelect #: PS16730838
Manufacturer #: W11594027
The light socket on your electric range connects the power source to the light bulb. If your oven light is malfunctioning, you may need to replace the light socket. The light socket is located in the ...
$59.65
In Stock
Surface Burner Valve - 16K - Left Front & Right Front
PartSelect #: PS11750353
Manufacturer #: WPW10206288
This is a surface burner valve for the left front and right front of your range. Burner valves are attached to the main gas line. When the switch is turned the gas then flows into a tube that mixes wi...
$78.35
In Stock
Questions And Answers for MGT8720DH06
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the MGT8720DH06
[Viewing 5 of 5]Will Not Start
Fixed by
these parts
these parts
Show All
Little to no heat when baking
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Burner valve was seized
Lock the oven/stove controls by holding the START button for five seconds. This shuts off gas to the valve. Remove the knobs from the front of the stove using philips screwdriver. Undo the six screws that hold on the front bezel and remove to find the valve. Unscrew the top bracket using philps screwdriver. disconnect the valve using
... Read more
a wrench (I think it was 12mm). Compare the valve to the new one. Installation is reverse. Press the START button for five seconds to unlock the oven/stove. Test fire the burner. Cook a batch of chili.
Read less
Parts Used:
-
Steve from Tracy, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
82 of 92 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ignitor was bad on upper oven
First I removed the lower tray and all parts covering the ignitor on the upper oven. 2. Then I removed the screws holding down the ignitor and flame distributor. 3. I then had to pull out the oven from the wall and remove the back panel to expose the wires connecting the ignitor. This required the removal of about six screws but they
... Read more
were fairly easy to get to. 4. I disconnected the ignitor from the back panel then went around to the front of the oven and pulled out the ignitor and all of the attached parts. 5. Here's the tricky part. The screws holding the ignitor in place had fused from the heat and then the threads stripped when I tried to remove them. I had to use a dremel tool and cutting wheel to carefully cut the screws off and then went to buy some replacement screws from the hardware store. 6. I replaced them with a nut and a bolt, to hopefully avoid the same problem for later replacement if necessary. 7. I then replaced everything the same way it came out and all is working like new!
Read less
Parts Used:
-
David from Temple Terrace, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
75 of 86 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Socket Light had a bad thread
Socket Lite come with clips attached to the outside
of the housing. After you unhook the 3 lead wires
that are attached to the unit. All you have to do is push in on the clips and release the unit. Then you
snap in the new unit. Attach the 3 wire leads, put a
oven bulb in the socket end, and the install the light cove ... Read more r
of the housing. After you unhook the 3 lead wires
that are attached to the unit. All you have to do is push in on the clips and release the unit. Then you
snap in the new unit. Attach the 3 wire leads, put a
oven bulb in the socket end, and the install the light cove ... Read more r
Read less
Parts Used:
-
Edmund from Emporium, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
44 of 65 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!