Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This door seal, also known as a door gasket, is an authentic manufacturer replacement part for your dishwasher. It is responsible for creating a watertight seal between the tub and dishwasher door and...
$43.00
In Stock
Order now and your part arrives in 2-3 business days!
A holder is used in dishwashers, it is known as the dishrack stop kit. This kit comes with both the front and the rear stop, these parts are installed at either end of the rails that the upper rack sl...
$12.01
In Stock
Order now and your part arrives in 2-3 business days!
This detergent and rinse aid dispenser is an important part in your dishwasher. It is located on the inside of the door and it holds and releases the detergent during the wash cycle of your dishwasher...
This check valve is a genuine OEM part that is compatible with several different makes and models of dishwasher. A check valve is designed to prevent the backflow of dirty water, food waste, and debri...
$17.26
In Stock
Order now and your part arrives in 2-3 business days!
This OEM-sourced detergent dispenser cover, also known as a rinse aid dispenser lid, seals and protects the detergent compartment in your dishwasher. Typically located on the inner door, it covers the...
$18.57
In Stock
Order now and your part arrives in 2-3 business days!
Here are the steps you need to take to do the job properly:
1. turn off electrical circuit breaker to the dishwasher 2. remove 8 total hex screws (3 on each side and 2 at the top) of the inside door panel. The door panel will slide off so be careful and it happens pretty quickly when the last hex screw is removed. 3
... Read more. unplug the wiring harness to the detergent/rinse aid dispenser 4. you need to use a flat head screw driver to lift the metal flanges on the top and bottom of the detergent/rinse aid dispenser. 5. the unit will pop out toward the inside of the dishwasher 6. insert the new detergent rinse/aid dispenser and very important all metal flanges are pulled back over the plastic edge (top and bottom) of the dispenser unit. The screw driver needs to be used to assist in pushing the dispenser unit as tight to the frame of the door to ensure the metal flanges grab hold and lock in. 7. re-attach the wiring harness 8. re-install the dishwasher door with 8 hex screws. Doing this step alone is challenging as the door frame will want to keep going up to close. I used a small foot stool and placed it inside the dishwasher front area on top of the inside metal door area so the door would stay open roughly half way. I then used my knees to prop up the outer door cover while i got 2 screws started then was able to easily complete the job. 9. run the dishwasher with a detergent packet loaded into your new dispenser. I checked for 15-20 minutes during initially running to insure no issues or leaks. 10. One last note - my Bosch dishwasher had a custom wood door installed to the outer panel to blend in with our kitchen cabinets. The door itself was much heavier as a result. Some of you may not experience the slight difficulty i noted above in step 8. Good luck.
I used a wet vac to remove the water from the dishwasher. remove cover and filter/strainer from bottom of dishwasher. remove screw which allows you to lift the plastic piece to access check valve. Original check valve looked like new , I installed new check valve re installed parts . Job done and issue resolved .
There are two ways to do this repair: the "right" way and the hard way. I chose the hard way, as the right way involves disconnecting the dishwasher plumbing, removing the dishwasher from under the counter, taking all the outer panels off, and disabling the door springs. There are good YouTube videos on this. The hard way doesn't invol
... Read moreve that -- but is not all that easy and I'm not sure I'd recommend it. The problem, in essence, is that to install the new seal there is now way to do it without taking the door off the machine and taking the door apart -- which requires that the springs be locked out, if not disabled.
I accomplished that part of it by opening the door, partially, undoing the two screws on each side which hold the hinges, taking the front panel off (piece of cake, with a Torx driver),slipping the door partly off the hinges, and then locking the hinges open with the pry bars.
There are an assortment of ways one could seriously damage either the door or one's self doing it that way -- the hinge springs are very powerful -- so I don't recommend my approach.
