SM115JXW1 Frigidaire Washer - Overview
Sections of the SM115JXW1
[Viewing 6 of 6]
Keep searches simple, eg. "belt" or "pump".
Water Inlet Valve
PartSelect #: PS815509
Manufacturer #: 134190200
The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the water inlet valve i...
$93.05
In Stock
Screw
PartSelect #: PS417463
Manufacturer #: 131302800
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$21.95
In Stock
Upper Spin Bearing Washer
PartSelect #: PS473382
Manufacturer #: 5308002401
The upper spin bearing for a washer can solve many issues such as loud and odd noises, or leaking water. Replacing the spin bearing could solve these issues. The tools needed for this replacement are ...
$22.95
In Stock
Levelling Leg Pad
PartSelect #: PS417749
Manufacturer #: 131422100
Sold Individually.
No Longer Available
Washing Machine Bolt
PartSelect #: PS3655064
Manufacturer #: 137539500
Holds plated on Trunion .312-18 x 1.625.
$28.95
In Stock
Upper Lip Seal
PartSelect #: PS454174
Manufacturer #: 5303161307
This basket drive tube seal or upper lip seal is used for a top washer and is located on top of the transmission, below the agitator drive block. The tube seal functions as a protective tool to preven...
$29.95
In Stock
Questions And Answers for SM115JXW1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the SM115JXW1
[Viewing 3 of 3]Leaking
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer Continued To Fill To Point Of Overflow
First I removed the top panel held by four screws at rear of panel, pulling the panel foward and up. Then disconnected the power and water connections. Then I removed the two screws holding the flow valve to the washer rear panel,pulled the valve foward ,removed the two electric connectors, pinched the water clamp with pliers and remo
... Read more
ved the water connection to the valve. Then replaced with the new valve followed the above steps in reverse order, finishing up by re placing the water connections and power. Then checked fo proper replacenent and leaks before replacing top panel.
Read less
Parts Used:
-
alvaro from east hampton, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
86 of 97 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No Cold Water
Checked problem on-line and discovered it was the water inlet valve. Matched the part on part select. Com. Finding the part was very easy. Part select had a grid behind the picture to help determine the size and pictures from all sides. Removing the old part, matching it, and replacement took a total of 30 minutes. I now have cl
... Read more
ean clothes.
Read less
Parts Used:
-
Mark from Pittsburgh, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
17 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
belt worn causing machine to make all kinds of noise
pull up on top ,take two screws loose on front panel(pull off) vaccum old debri out,pull tension pulley back pull old belt off,holding tension pulley put new belt on .put front panel back on and snap top back down to secure.
working perfectly nice and quite !!!
working perfectly nice and quite !!!
Parts Used:
-
Kenneth from Baltimore, MD
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
19 of 26 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!