WF206LNWXAC Samsung Washer - Overview
Sections of the WF206LNWXAC
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Washer Door Lock Latch
PartSelect #: PS11745016
Manufacturer #: WP8182634
This part is used on front load washers and includes the interlock switch assembly.
$81.43
In Stock
Washer Drain Pump (120V)
PartSelect #: PS4204638
Manufacturer #: DC31-00054A
This is a 120 volt, 60 hertz drain pump assembly for a washing machine. It is a genuine OEM part. This pump helps expel water from the washing machine, and is activated after the spin speed is maintai...
$163.30
In Stock
Washer Inlet Hose 5 Ft
PartSelect #: PS11746820
Manufacturer #: WP89503
This hose can handle hot or cold water and is five feet long.
$16.63
In Stock
Washer Hex Bolt
PartSelect #: PS4205366
Manufacturer #: DC60-40137A
This part is used for the shaft on the rear of the tub and is sold individually. The head bolt is part of the spider arm assembly, and they are generally changed at the same time. If you are replacing...
$11.95
In Stock
Water Valve
PartSelect #: PS4209100
Manufacturer #: DC62-30314K
One solenoid valve for hot water
$84.95
In Stock
Bolt Assembly
PartSelect #: PS4217876
Manufacturer #: DC97-02412A
Assembly BOLT;SWF-P12,MOTOR/
$22.95
In Stock
Door Glass
PartSelect #: PS4210731
Manufacturer #: DC64-00504C
Explore the sturdiness and functionality of the Samsung Washer Door Glass. Fitting perfectly with a set of Samsung Washer models, it is a high-quality door glass, designed with an eye for detail by Sa...
$155.15
On Order
Washer Tub Gasket Seal
PartSelect #: PS4213806
Manufacturer #: DC69-00804A
This is a seal for various models of Samsung washing machines. This part acts as a seal for the rear and front outer part of your washing machine tub and is used to prevent any matter of leaks. If you...
$35.95
In Stock
Questions And Answers for WF206LNWXAC
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the WF206LNWXAC
[Viewing 6 of 6]Lid or door won’t close
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Locking Issues
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
front load washer latch replacement
1. remove the three screws from the top backside of the top panel
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using to ... Read more p opening.
7. reverse order to finish.
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using to ... Read more p opening.
7. reverse order to finish.
Read less
Parts Used:
-
James from Vilonia, AR
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
196 of 238 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door lock was in the locked position and door could not close
I bought a new door lock for 132 dollars (item number PS2037196).
Ultimately you have to get to the inside of the machine where the door lock is located in order to see if you will need this door lock that I bought.
DISCONNECT POWER FROM MACHINE.
First take off the top by taking off the 2 screws on the bac ... Read more k of the machine.
Second take off the control panel, I believe there are about 5 or 6 screws for that.
(there's also a screw when you open up the detergent compartment on the bottom left- also, a lever must be pushed in order for the compartment to come off- it MUST be taken off).
Third unscrew the top of the front white plate.. there should be a 5 or 6 screws for that.
You don't need to take off the entire front plate.
Finally unscrew 3 screws that hold the door lock in place .. make sure your hands is in the machine- the back of door lock to catch the lock when you're on the last screw.
Gently take out the door lock from the side with the cables attached by holding the white metal door open (it bends).
Try to pull on the bottom of the door lock (its a manual release). If it doesn't release you need to buy a new door lock like I did... if it does release then you don't need a door lock and just reassemble.
(Note: You can also try plugging in the machine and THEN pulling down on the manual release. When I tried this the door lock just vibrated and nothing happened so I bought a new door lock.)
If you have the new door lock continue here:
Take out all 3 cables on the old door lock by pressing on the corresponding clips.
Attach the new door lock with the correct cables. Assemble machine back together.
Thats it.
Ultimately you have to get to the inside of the machine where the door lock is located in order to see if you will need this door lock that I bought.
DISCONNECT POWER FROM MACHINE.
First take off the top by taking off the 2 screws on the bac ... Read more k of the machine.
Second take off the control panel, I believe there are about 5 or 6 screws for that.
(there's also a screw when you open up the detergent compartment on the bottom left- also, a lever must be pushed in order for the compartment to come off- it MUST be taken off).
Third unscrew the top of the front white plate.. there should be a 5 or 6 screws for that.
You don't need to take off the entire front plate.
Finally unscrew 3 screws that hold the door lock in place .. make sure your hands is in the machine- the back of door lock to catch the lock when you're on the last screw.
Gently take out the door lock from the side with the cables attached by holding the white metal door open (it bends).
Try to pull on the bottom of the door lock (its a manual release). If it doesn't release you need to buy a new door lock like I did... if it does release then you don't need a door lock and just reassemble.
(Note: You can also try plugging in the machine and THEN pulling down on the manual release. When I tried this the door lock just vibrated and nothing happened so I bought a new door lock.)
If you have the new door lock continue here:
Take out all 3 cables on the old door lock by pressing on the corresponding clips.
Attach the new door lock with the correct cables. Assemble machine back together.
Thats it.
Read less
Parts Used:
-
Suryakant from Cortlandt Manor, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
66 of 73 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Washer became unbalanced and broke the latch on door
Had to take the entire front of the washer off to replace the door latch.
Parts Used:
-
Glenn from Las Vegaas, NM
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
30 of 39 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!