WF330ANW (XAA-0006) Samsung Washer - Overview
Sections of the WF330ANW
[Viewing 7 of 7]
Keep searches simple, eg. "belt" or "pump".
Washer Hex Bolt
PartSelect #: PS4205366
Manufacturer #: DC60-40137A
This part is used for the shaft on the rear of the tub and is sold individually. The head bolt is part of the spider arm assembly, and they are generally changed at the same time. If you are replacing...
$11.95
In Stock
Shock Damper
PartSelect #: PS4212220
Manufacturer #: DC66-00470B
This is an individually sold shock absorber designed for use within Samsung washing machines. This rear shock absorber is designed to evenly distribute the weight and prevent the excessive vibrations ...
$45.95
In Stock
Shock Damper
PartSelect #: PS4212219
Manufacturer #: DC66-00470A
This is an individually sold front shock absorber designed for use with Samsung dryers. Shock absorbers are used to distribute the weight of the dryer drum evenly and ensure that the different bumps a...
$69.95
In Stock
Outer Seal Clamp
PartSelect #: PS4218211
Manufacturer #: DC97-04973B
This is an outer seal clamp for the washer door boot of your Samsung washing machine. This clamp tightly seals the boot of the drum within the door of the washer to prevent leaks. This clamp is made o...
$12.95
In Stock
Water Valve
PartSelect #: PS4209100
Manufacturer #: DC62-30314K
One solenoid valve for hot water
$84.95
In Stock
Drain Pump
PartSelect #: PS4204640
Manufacturer #: DC31-00054D
This is the drain pump assembly for various models of Samsung washing machines. The drain pump is used to remove any water from the washer after it has completed its washing cycle. If your washer stil...
$48.95
In Stock
Door Lock Switch
PartSelect #: PS4205052
Manufacturer #: DC34-00024B
This part is a door lock switch assembly, and it is made to work with your washing machine. The purpose of your door switch is to lock the door of your washer during the washing cycle. This will preve...
$131.95
In Stock
Flange And Shaft Assembly
PartSelect #: PS4220876
Manufacturer #: DC97-15491A
Introducing a high-functioning and genuine Samsung replacement part, a Washer Inner Tub Flange and Shaft Assembly. This essential piece aids in connecting the spin basket to the drive motor, allowing ...
$216.55
In Stock
Water Temperature Thermistor
PartSelect #: PS4214274
Manufacturer #: DC90-10128N
The thermistor monitors and helps regulator the water temperature in the washer.
$54.95
On Order
Door Glass
PartSelect #: PS4210731
Manufacturer #: DC64-00504C
Explore the sturdiness and functionality of the Samsung Washer Door Glass. Fitting perfectly with a set of Samsung Washer models, it is a high-quality door glass, designed with an eye for detail by Sa...
$155.15
On Order
Pressure Switch
PartSelect #: PS4217080
Manufacturer #: DC96-01703B
The pressure switch senses and controls the water level in the washer.
$76.95
In Stock
Washer Tub Gasket Seal
PartSelect #: PS4213806
Manufacturer #: DC69-00804A
This is a seal for various models of Samsung washing machines. This part acts as a seal for the rear and front outer part of your washing machine tub and is used to prevent any matter of leaks. If you...
$35.95
In Stock
Questions And Answers for WF330ANW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the WF330ANW
[Viewing 4 of 4]Shaking and Moving
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The water level was lower than normal.
First unplug or turn off thee circuit breaker. Then remove the two screws to the top cover. Slide the cover back about three inches then remove the cover. Next take out the screw to the old sensor. Then unplug the electrical connection by squeezing and the pulling to disengage. Now set the old unit aside. You then grad your eight inch wi
... Read more
re tie and hold the with flat side to the right and just to the right of the screw hole for the bracket is a square hole. Feed to wire tie into the square hole with your left hand then loop down left side of the end of new sensor and back up threw the square hole and tighten with the pliers. Your new sensor will be positioned just like it was mounted to the metal bracket. And pretty ridged. Now connect the vacuum hose and electrical connector.
Read less
Parts Used:
-
Fredric from ROCKMART, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
3 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Was not spinning out
-
Walter from BROOKLYN, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers, Socket set
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer making noise a snow smoking.
Take pics every step, easier re-assembly. Dismantled washer keeping bolt/screw section removed compartmentalized in a tackle box in the order of removal. Replaced drum support, bearings, seal, old blots. Too much to write but I was able to do it all in about 4 hours once all the parts finally came in.
Parts Used:
-
Samuel from NEEDVILLE, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set, Wrench set
14 of 54 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!