WR-HC137UH Samsung Washer - Overview
Sections of the WR-HC137UH
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Washer Hex Bolt
PartSelect #: PS4205366
Manufacturer #: DC60-40137A
This part is used for the shaft on the rear of the tub and is sold individually. The head bolt is part of the spider arm assembly, and they are generally changed at the same time. If you are replacing...
$11.95
In Stock
Bolt Assembly
PartSelect #: PS4217876
Manufacturer #: DC97-02412A
Assembly BOLT;SWF-P12,MOTOR/
$22.95
On Order
Water Temperature Thermistor
PartSelect #: PS4214274
Manufacturer #: DC90-10128N
The thermistor monitors and helps regulator the water temperature in the washer.
$54.95
On Order
Door Glass
PartSelect #: PS4210731
Manufacturer #: DC64-00504C
Explore the sturdiness and functionality of the Samsung Washer Door Glass. Fitting perfectly with a set of Samsung Washer models, it is a high-quality door glass, designed with an eye for detail by Sa...
$155.15
On Order
Pressure Switch
PartSelect #: PS4217080
Manufacturer #: DC96-01703B
The pressure switch senses and controls the water level in the washer.
$76.95
In Stock
Tub Bearing
PartSelect #: PS4133788
Manufacturer #: 6601-000148
Upgrade your washing machine with this high-quality tub bearing from Samsung. Precision designed, this ball bearing enhances the function of your machinery, offering smooth and efficient rotation for ...
$84.95
In Stock
Drain Cap
PartSelect #: PS4207510
Manufacturer #: DC61-10673A
This drain cap is a genuine replacement part made for Samsung washers. It is a small plastic cap, approximately 1.5 inches long, that fits onto the end of the washing machine drain hose. The cap is re...
$6.95
In Stock
Door Lever
PartSelect #: PS4212119
Manufacturer #: DC66-00326A
This is a door lever strike for Samsung washing machines. This part is used to latch and hold the washer door to the washer door frame when it is closed. If the door strike for your washer is currentl...
$12.95
On Order
Questions And Answers for WR-HC137UH
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The water level was lower than normal.
First unplug or turn off thee circuit breaker. Then remove the two screws to the top cover. Slide the cover back about three inches then remove the cover. Next take out the screw to the old sensor. Then unplug the electrical connection by squeezing and the pulling to disengage. Now set the old unit aside. You then grad your eight inch wi
... Read more
re tie and hold the with flat side to the right and just to the right of the screw hole for the bracket is a square hole. Feed to wire tie into the square hole with your left hand then loop down left side of the end of new sensor and back up threw the square hole and tighten with the pliers. Your new sensor will be positioned just like it was mounted to the metal bracket. And pretty ridged. Now connect the vacuum hose and electrical connector.
Read less
Parts Used:
-
Fredric from ROCKMART, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
3 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer making noise a snow smoking.
Take pics every step, easier re-assembly. Dismantled washer keeping bolt/screw section removed compartmentalized in a tackle box in the order of removal. Replaced drum support, bearings, seal, old blots. Too much to write but I was able to do it all in about 4 hours once all the parts finally came in.
Parts Used:
-
Samuel from NEEDVILLE, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set, Wrench set
14 of 56 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!