WSM2781WCWWW General Electric Washer Dryer Combo - Overview
Sections of the WSM2781WCWWW
[Viewing 6 of 6]
Keep searches simple, eg. "belt" or "pump".
Lower Front Felt Seal w/Adhesive
PartSelect #: PS832645
Manufacturer #: 5303937183
The lower front felt seal with adhesive, also known as a drum felt seal, is used in dyers and allows the drum to easily glide on the front panel. For this repair project, you will need the following t...
$28.95
In Stock
DRYER LINT FILTER
PartSelect #: PS12741280
Manufacturer #: WE16X29397
This is the replacement lint filter for your dryer. The lint filter traps unwanted lint and debris so your dryer can effectively dry your clothes.
No Longer Available
Timer Knob - Dryer
PartSelect #: PS755794
Manufacturer #: WE01X10160
Used with washer/dryer combo machines. This knob takes a D-shaped shaft.
$66.59
In Stock
Rear Bearing
PartSelect #: PS267858
Manufacturer #: WE3X70
Bearing Only. This part helps your appliance run as quietly as possible.
No Longer Available
Drum Glide
PartSelect #: PS755802
Manufacturer #: WE03X10007
Sold individually. There are some dryers that require 2 per dryer. They attach to the outer-most sides of the bearing.
$65.29
In Stock
Dishwasher Hose Clamp Kit
PartSelect #: PS270806
Manufacturer #: WH1X2036
This is a water hose clamp kit for a variety of appliances including dishwashers and washers. This is a genuine replacement part. The kit includes two hose clamps. The smaller of the two is 1 inch in ...
$22.95
In Stock
Rear Bearing Shaft Support
PartSelect #: PS265828
Manufacturer #: WE13X10011
Introducing the GE Dryer Drum Bearing! This genuine replacement part is the ultimate solution for enhancing your dryer's performance. It is ideal for supporting the drum as it spins, offering stabilit...
$97.96
In Stock
DRYER BEARING BRACKET
PartSelect #: PS12710145
Manufacturer #: WE13X28680
This bracket is used on the drum bearing.
$45.95
In Stock
Drain Pump
PartSelect #: PS3502779
Manufacturer #: WH23X10041
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
No Longer Available
V-Belt
PartSelect #: PS960606
Manufacturer #: WH07X10009
Introducing the Genuine GE Appliances Drive Belt, a crucial component for your washing machine. Known as the V-Belt, it expertly bridges the connection between the drive motor and the machine's drive ...
$85.21
In Stock
Upper Felt Seal with Adhesive
PartSelect #: PS652857
Manufacturer #: WE09X10013
Experience smooth operation with this genuine Dryer Felt Seal from GE. This product is designed to allow your dryer drum to glide effortlessly on the front panel, promising a quieter, more efficient p...
No Longer Available
Questions And Answers for WSM2781WCWWW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the WSM2781WCWWW
[Viewing 5 of 5]Noisy
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer would not drain
Removed 2 Hose clamps with pliers. Unplug power source from drain pump. Unscrew 2 mounting screws with 5/16" nut-driver then replace unit in reverse sequence...... Very simple.
Parts Used:
-
Jack from Canyon Lake, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
26 of 40 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
filter had a hole
-
Patricia from chicago, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
14 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Felt around drum holder worn and torn.
1. Removed face of dryer (drum 'holder')
2. Disconnected door switch wires
3. Tore off existing felt
NOTE: The length of the felt that I recieved from PartSelect was incorrect (too short). Since the existing felt was worn and torn at the top, I replaced only a length that matched the length of the new felt.
... Read more >4. Used a razor blade-type gasket remover/scraper to remove the exisitng glue
5. Applied new glue (which comes with the felt) onto the felt and let it set up
NOTE: In hindsite, I would apply the glue to the drum holder instead, as the glue otherwise soaks into the felt. If applied to the drum holder instead, the glue will spread out and provide more surface area for adherence.
6. Installed the new felt, starting at one end and working my way around to the other end, being careful not to stretch it
7. Trimmed the remainder of the existing felt (see first NOTE)
8. Scraped the drum holder below the pulled away ends of the exisitng felt
9. Applied glue to the existing felt, including the trrimmed ends so that the ends do not pull away from the ends of the new felt
10. Re-attached the existing felt
11. Let the glue set-up overnight
12. Reinstalled the face of the dryer, turning the drum so that the felt will not get pushed away
13. Reconnected the door switch wires
14. Turned dryer on, with lid still raised, to check for any drifting of the felt
15. Once assured that the felt would stay in place, put the dryer in service
NOTE: I replaced the felt becasue of the gap that opened due to compression of the felt. The gap, as well as a torn piece of the felt that entered the interior of the drum, was catching clothes and tearing them as they were rotated between the drum and the drum holder. The new felt eliminated this problem.
2. Disconnected door switch wires
3. Tore off existing felt
NOTE: The length of the felt that I recieved from PartSelect was incorrect (too short). Since the existing felt was worn and torn at the top, I replaced only a length that matched the length of the new felt.
... Read more >4. Used a razor blade-type gasket remover/scraper to remove the exisitng glue
5. Applied new glue (which comes with the felt) onto the felt and let it set up
NOTE: In hindsite, I would apply the glue to the drum holder instead, as the glue otherwise soaks into the felt. If applied to the drum holder instead, the glue will spread out and provide more surface area for adherence.
6. Installed the new felt, starting at one end and working my way around to the other end, being careful not to stretch it
7. Trimmed the remainder of the existing felt (see first NOTE)
8. Scraped the drum holder below the pulled away ends of the exisitng felt
9. Applied glue to the existing felt, including the trrimmed ends so that the ends do not pull away from the ends of the new felt
10. Re-attached the existing felt
11. Let the glue set-up overnight
12. Reinstalled the face of the dryer, turning the drum so that the felt will not get pushed away
13. Reconnected the door switch wires
14. Turned dryer on, with lid still raised, to check for any drifting of the felt
15. Once assured that the felt would stay in place, put the dryer in service
NOTE: I replaced the felt becasue of the gap that opened due to compression of the felt. The gap, as well as a torn piece of the felt that entered the interior of the drum, was catching clothes and tearing them as they were rotated between the drum and the drum holder. The new felt eliminated this problem.
Read less
Parts Used:
-
Robert from York, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
10 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!