WT1801HWA (ABWEVUS) LG Washer - Overview
Sections of the WT1801HWA
[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
Water Inlet Valve
PartSelect #: PS12374721
Manufacturer #: AJU75152601
This is an authentic LG water inlet valve for a top-load washer. It is designed to control the flow of water into the washer. If your washer is filling slowly, making loud noises, overflowing, or stop...
$147.13
In Stock
Washer Pulsator Cap
PartSelect #: PS3525704
Manufacturer #: 5006EA3009B
This part is known as a pulsator cap or washplate cap, and is designed for your LG washer. It fits over the washplate mounting bolt and prevents clothes from getting caught on the washplate during a w...
$44.83
In Stock
Washer Drain Pump Assembly
PartSelect #: PS11706439
Manufacturer #: 5859EA1004P
This drain pump is for washers. Drain pump removes water from the washer during the drain portion of the cycle. Unplug the washer before installing this part. Wear work gloves to protect your hands.
$174.98
In Stock
Washer drain Hose Assembly
PartSelect #: PS3617213
Manufacturer #: AEM73213001
This is a drain hose assembly for top-load models of LG washing machines. This hose specifically is used to allow water to drain from the tub to the drain pump of the washer. This hose is made of plas...
$40.88
In Stock
Washer Hinge
PartSelect #: PS7795475
Manufacturer #: MEF62462103
Upgrade your LG washing machine with this genuine top lid hinge. Specially designed to support the hinge and help cushion the lid when opening and closing, this high-quality component ensures the long...
$13.75
In Stock
Screw
PartSelect #: PS3534421
Manufacturer #: FAB30598601
Introducing the customized screw designed exclusively for LG washers. Manufactured with safety and efficiency in mind, installation is straightforward when you adhere to correct safety regulations. Sh...
$20.67
In Stock
Washer Switch Assembly sensor
PartSelect #: PS3529177
Manufacturer #: 6501EA1001R
This water-level pressure switch in your wash monitors and regulates the water levels throughout the fill, wash, and rinse cycles. You will usually find it inside the control panel or near the tub. It...
$63.16
In Stock
HOUSING ASSEMBLY,CLUTCH COUPLING
PartSelect #: PS12580053
Manufacturer #: AEN73651402
This clutch housing assembly with mode shifter, or washer drive shaft and shifter assembly, is made for your washer. It connects the appliance wash plate to the motor so the washer can shift the drive...
$276.55
In Stock
Washer Drive Shaft And Shifter Assembly
PartSelect #: PS7788161
Manufacturer #: AEN73131403
HOUSING ASSEMBLY,CLUTCH
This drive shaft and shifter assembly (part number AEN73131403) is for washers.
Drive shaft and shifter assembly AEN73131403 connects the motor with the washplate, and shif...
No Longer Available
Questions And Answers for WT1801HWA
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the WT1801HWA
[Viewing 10 of 10]Leaking
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Water Filling Issues
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Draining Issues
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
It did not drain water, cycle stops at rinse+spin.
1-Take water off manually. 2- Take machine to back yard. 3- lay machine 45 degrees. 4- Located water bump, (rear left side). 5-removed drain black hoses with hand. 6-removed 3 screws from bump frame. 7-Taker off all unit and marked down cable position at plug. 8- installed new pump. 9- Reverse all steps. Note: I did not use new cable su
... Read more
pplied with the new bump, I did not want to mess around on mother board connections, I kept old wire harness which are only two cables blue and gray. It took me less than 30 minutes.
Read less
Parts Used:
-
Jesus from El Paso, TX
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set, Wrench set
23 of 30 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The right side hinge that holds the washer top door broke and needed to be replaced.
Popped out the plastic "doors" that cover the metal actuators. Removed the metal actuators on both right and left sides of the door then unscrewed (3 screws each actuator) them from door frame. Slid the actuators out to enable the door to be removed. Unscrewed 2 screws on the top front of the washer which enabled me to angle the top of
... Read more
the washer to expose the screws that hold the plastic hinges. Unscrewed the hinges (2 screws each) and replaced both of the hinges (I figured I'd do both of them now so I don't have to do it again for another 15 years). Put everything back together and all works like new.
Read less
Parts Used:
-
John from SAN JOSE, CA
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
12 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water continued leaking into washer after the end of cycle through the water inlet valve.
-
Flora from MIAMI, FL
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench (Adjustable)
12 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!