Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
OEM stands for Original Equipment Manufacturer. Simply put, this means that the company who made your appliance is also supplying the replacement part for it.
OEM from PartSelect
Genuine brand name
Guaranteed to fit
Superior quality and durability
1 year warranty
Generic
Unknown manufacturer
No fit guarantee
Inconsistent quality and lifespan
Limited warranty and support
Troubleshooting
Part# W10860464 replaces these:
AP6026286, WPW10571743
Customer Repair Stories
Average Repair Rating: 4.9 / 5.0, 1 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
machine was showing all lights and wouldn't start up
unplugged machine removed front panel .disconnect wiring harnesses . pop out old control ,install new reconnect wiring put back in place resecure and plug in and test
Angel from MILWAUKEE, WI
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jim
October 22, 2017
All the lights are on at the same time and the washer won't start
For model number CAE2743BQ0
Hi Jim,
Thank you for your question. You could try unplugging your appliance from the power for about 5 minutes and then plugging your appliance back in again. If you still have the problem, then you will need to replace your control board. Good luck with your repair.
6 people found this helpful.
Was this helpful?
Thank you for voting!
Brent
February 14, 2018
Lid lock keeps flashing and i can hear clicking but won't lock and machine stays in sensing mode
For model number CAE2743BQ0
Hi Brent, Thank you for the question. This means the lock switch is defective and the lid lock needs to be replaced. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Drew
December 10, 2019
The “sensing load” light comes on, and the washer begins to fill with water, but the water only runs for about 20 seconds and then stops. When the washer was empty it ran through a whole cycle except for the final spin, but with a small load in it the machine won’t go past “sensing load”. That light went out after about 10 minutes, and about five minutes after that the discharge pump came on and ran for about 5 minutes. Only a small amount of water came out, and i checked hose for blockages. After the pump shut off the “sensing load” light, the “rinse” light and the “done” light all came on at the same time. Any ideas?
For model number CAE2743BQ0
Hello Drew, thank you for your question. It sounds like there may be an issue with the pressure switch or pressure hose. We would recommend replacing those parts first. The pressure switch is part of the board PartSelect Number PS11737994. If the issue persists, the problem could be with the lid switch. I hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Bridgette
September 27, 2017
I'm trying to find the serial number and p/n number for the above model for the main control board
For model number WTW4880AW0
Hi Bridgette,
Thank you for your question. I have attached the link to the part down below for you. Good luck with your repair.
I used to have the issue where, after a load, all lights would be on and the machine would eat quarters and not start until after the machine was reset via diagnostics mode. I replaced the control board, and the machine worked flawlessly for maybe six months, but now it's having the same issues again, but worse. It seems like the machine needs to be reset twice and then it works again. What could the issue be?
For model number CAE2743BQ0
Hello Kenny, thank you for getting in touch. Based on our understanding of the issue, we would suggest you checking the control panel, part number PS7320635, to fix the issue. We hope this helps!
