Refrigerator Housing Water Filter WP2186443

Hi Sue, Thank you for the question. Please see the link below to the video on how to install the filter for your model number. Hope this helps! https://www.youtube.com/watch?v=yM8Pr0F3rpc

Hi Mark, Thank you for the question. You will need to replace the filter housing, Part Number: PS11739083 since the fittings are not sold separately. The water line can be used with the new filter housing. Hope this helps!

Hello Terry, Thank you for your inquiry. Part# WP2256096 is the ice maker water inlet tube and fitting. These instructions may not apply step by step to your model, but are to give you a general idea of the procedure. Pull out the fridge and remove the rear access panel at the bottom with a 1/4 inch nut driver. Remove the screws at the bottom holding the line at the bottom and use a 5/16 wrench to push on the locking collar and disconnect the line from the water valve-you may need to pull the valve out. You may want to put a towel down to catch any leaking water. Now move to the front of the fridge and open the freezer door. Remove the shelves, and remove the cover over the ice maker. Use the 1/4 nut driver to remove the screw at the bottom right of the ice maker and remove a cover that is there. Using a flat blade screw driver, press on the locking tab on the left side of the ice maker and pull it out, close the flapper door and pull out the ice maker assembly, then use the screw driver to disconnect the ice maker wiring harness. You should now be able to see the fill tube of the ice maker, which is what you would need to pull out. Rock the fitting from side to side and gently pull it loose. Slowly pull it down, and make note that it is installed sideways. Keep pulling until the supply tube is completely out. Thread the tube of the new supply line into the opening, you should be able to see it come out of the hole at the back, and keep pushing it through until you can place the nozzle in sideways. You make need to go to the back of the fridge and gently tug at the tube if the nozzle will not go all the way in. Once it is back in place, reconnect the icemaker harness and replace the icemaker, making sure the tip of the tube is over the water inlet cup. Put the cover on, and replace the screws, and slide the access door back on. Replace the shelf. Now go to the back of the fridge and push the end of the supply line into the water inlet valve, making sure it is tight. Replace the water valve and retainer clip. Re-install the access panel. Hope this helps!

Hello, Thank you for contacting us. I have researched the model you have provided and have found the part you’re looking for is Part Number: PS11739084 for the Black Option, Part Number: PS11739085 for the bisque and Part Number: PS11739086 for white. Thank you for your inquiry, good luck with this repair!

Hello Bruce, Thank you for the question. Sounds like a leak in the water line. The only way to know for sure woudl be to take the dispenser apart and check to see if the line is damaged or something has come lose within the dispenser. Thank you for your inquiry, good luck with this repair!

Hi Ash, Thank you for your question. If you recently replaced your water filter and you did not flush it before use, this would account for the chemical taste you experienced. There are videos on YouTube that you may reference on how to flush a water filter, but for information related to your refrigerator, you will need to consult your owner's manual. I hope this helps. Thank you and have a great day!

Hello Ash and thanks for writing. Sorry to hear about your experience. In order to check into this for you please provide us with the following: Order number and Filter number. Please contact us through customerservice@partselect.com or call to speak to one of our agents 1-888-260-4310 Looking forward to hearing from you.

Hello Thomas, Thank you for the question. The Water Supply tube would connect to the Water Inlet Valve at the back of the appliance. We hope this helps.

Hi Bob, thank you for your question. The part you are requesting on has been discontinued and we have no known replacement listed in our system. We have no further information. You are welcome to contact the manufacturer of the part to see if they have recently released a new substitute. This was the part number: 9010. Good luck with your repair.

Hello Hoan, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS11739083. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!