Dryer Door Switch Assembly WP3406105

Hi Quan, thank you for getting in touch. Part number 3406104 was replaced by the manufacturer with part number WP3406105. That is the door switch assembly that is compatible with your appliance. I hope this helps!

Hello Peter, Thank you for the question. The manufacture has discontinued the old 2 wire switch and replaced it with this 3 wire switch. This switch is used on models that have a tub light and will require the third wire for the light. This switch is interchangeable with your switch and will still work. You just need to plug it in as you normally would have. Thank you for your inquiry, good luck with this repair!

Hi Jimmy, Thank you for the question. Yes, Part number 3406105 replaces 3406104. Hope this helps!

Hello Lee, Thank you for your inquiry. We show that this is the updated part number for the switch for the model number you provided. It should function the same as the original. Hope this helps!

Hi Alyce, Thank you for your question. The new switch comes attached to a clip. You just pull off the old clip and replace it with the new one and discard the old switch. If you have tried this you may have to consult your owner's manual for more information. I hope this helps. Thank you and have a great day!

Hi Gail, Thank you for your question. Here is some information that a customer has left regarding how she installed the switch, "Hi, I am a working mom, and my dryer quit just after it had been behaving strangely. At first, it kept spinning after the door was opened. It eventually stopped working, and I assumed that the door switch must be the culprit. I purchased the part from the catalogue, and watched the installation video. Repair: After unplugging the dryer and removing the lint screen, I used a philips head screwdriver to loosen and remove the two screws located at the lint trap. I then inserted a flat screwdriver into the area between the top of the dryer casing and the face. Per the video, at approx. 2 inches in from the left and right side. I did this while gently applying pressure from the back of the dryer top to the front. This loosens the clips allowing the top to be lifted back and out of the way. I then opened the dryer door and commenced loosening and removing the two screws that hold the dryer switch in place. I used my screwdriver to gently separate the wiring harness connection, as it also has a clip to keep the connection tight. With these items free, I simply popped the little black thingy back through the hole (The black thingy just keeps the slack in the wiring from sagging, I think). With the old part removed, I then installed the new part accordingly. I reversed my way back out of the process respectively. I plugged her back in, and turned her on. Back in business." I hope this helps. Thank you and have a great day!

Hi Carl, Thank you for your question. Here is some information that a customer has left regarding how she installed the switch, "Hi, I am a working mom, and my dryer quit just after it had been behaving strangely. At first, it kept spinning after the door was opened. It eventually stopped working, and I assumed that the door switch must be the culprit. I purchased the part from the catalogue, and watched the installation video. Repair: After unplugging the dryer and removing the lint screen, I used a philips head screwdriver to loosen and remove the two screws located at the lint trap. I then inserted a flat screwdriver into the area between the top of the dryer casing and the face. Per the video, at approx. 2 inches in from the left and right side. I did this while gently applying pressure from the back of the dryer top to the front. This loosens the clips allowing the top to be lifted back and out of the way. I then opened the dryer door and commenced loosening and removing the two screws that hold the dryer switch in place. I used my screwdriver to gently separate the wiring harness connection, as it also has a clip to keep the connection tight. With these items free, I simply popped the little black thingy back through the hole (The black thingy just keeps the slack in the wiring from sagging, I think). With the old part removed, I then installed the new part accordingly. I reversed my way back out of the process respectively. I plugged her back in, and turned her on. Back in business." I hope this helps. Thank you and have a great day!

Hello Debbie, thank you for your question. You would reach inside the unit and take the cover off the filter, then pull the filter out of the dryer. This should be done every load you do so as to prevent a fire, or cause drying time issues. I hope this helps!

Hello, thank you for your inquiry! We are showing that 3406104 has been replaced by PS11741700. We do not have any information about 3406107 being a compatible alternative. We hope this helps!

Hello Jeff, Thank you for contacting us. I suggest checking the following parts: PS3529161 Sensor, PS3529026 Thermistor,NTC, and PS11710693 PCB ASSEMBLY,MAIN. You can test the parts with a multimeter. If you are unfamiliar with how a multimeter functions, we have videos available to assist you.