Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
OEM stands for Original Equipment Manufacturer. Simply put, this means that the company who made your appliance is also supplying the replacement part for it.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jim Sitton
October 23, 2019
My jenn air model jds9860, continues to heat past bake set point the thermostat is working as it is reading temp as it heats to set point. The top element counties to stay on until overheat is reached. Would this be a faulty control board?
For model number 336-312-5289
Hello Jim, thank you for your question. This issue would be in relation to a bad sensor, or a bad electronic control board. To determine which is the problem test the sensor. It will need to be disconnected and tested with an ohm meter. At normal room temperature, the oven temperature sensor should have a resistance of 1050-1100 ohms. If it is not close to this it would need to be replaced. If the sensor is tested and reads within that range, the issue is the electronic control board and would have to be replaced. Good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jakki
January 23, 2020
Oven control panel shuts off and on intermittently and blinks when power returns. Is this faulty panel or power issue?
For model number JDS9860AAP
Hello Jakki, Thank you for the question. This sounds like a defective Electronic Control Board that may need to be replaced. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Ash
May 14, 2024
I just had this part replaced on my range from Jenn Air because it takes at least an hour for the oven to preheat to 350 Fahrenheit. Unfortunately, replacing this part did not help. There is nothing in the oven except for the racks that came with it. What should I do next? I am not sure if the burner element in the oven needs to be replaced.
For model number JDS9860AAP
Hello Ash, thank you for reaching out. According to our research, the issue is most probably with the temperature sensor, part number PS1570174. It measures the oven temperature and sends the information to the control board. You may need to replace it to fix the issue. We hope this helps!
Hello, my Jenn air range takes nearly an hour to preheat past 300 degrees. I believe it was only getting 120V. It’s not the elements (tested with multimeter) so I replaced the Electronic Control Board as suggested but this has not fixed the issue. Any other suggestions?
For model number JDS9860BCP
Hi Rick, thank you for reaching out. We suggest testing the oven sensor. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. Thank you for the inquiry, good luck with the repair!
Oven will not reach temp over about 250, temp sensor oms ok, so does lower heating element but it does not get very hot. Repairman says heating element is not getting 240v only 120v needs to replace the control panel, is this likely? Broiler works ok and convection fan comes on.
For model number JDS9860AAP
Hello Tom, Thank you for your inquiry. I would also check the high limit thermostat first, part# WP71001844. If the continuity on that checks out ok, then test the electronic control board. Good Luck with your repair!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11742969
Manufacturer Part Number: WP5760M302-60
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Range","title":"Range","url":"/Range-Parts.htm"},{"position":2,"name":"Circuit Board or Touch Pad","title":"Circuit Board or Touch Pad","url":"/Range-Circuit-Boards-and-Touch-Pads.htm"},{"position":3,"name":"WP5760M302-60","title":"WP5760M302-60","url":""}]
You added 1 item to your cart
✖
% OFF
$
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
