Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
This wash impeller is three inches in diameter. It is all gray in color and is made of plastic.
How Buying OEM Parts Can Save You Time and Money
Why buy the real thing?
OEM stands for Original Equipment Manufacturer. Simply put, this means that the company who made your appliance is also supplying the replacement part for it.
Not cleaning dishes properly | Noisy | Not draining
This part works with the following products:
Dishwasher.
Part# WP902461 replaces these:
9-2461, 902461
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
5.0
Filter By Rating:
5 Stars
1
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Anthony G - June 8, 2021
Verified Purchase
Easy Repair
Brand new Part
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 2.8 / 5.0, 7 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
On Thanksgiving weekend my poor 23 -year -old Maytag dishwasher started making a horrible grinding noise and wasn't cleaning anything. I washed more dishes by hand in 4 days than I have in the past 4 years.
My husband does all the repair work himself so he tore it all apart but it's hard to find parts for a 23 year old machine. A store about an hour from our house said they had the part. When we got there it was the wrong impeller and it was going to be $30 to order it in. I got home on that Weds. nite ordered it and had the part 2 days late
... Read morer on that Friday.My husband had the part in and the dishwasher running within 20 minutes. Thrilled with the fast service from you and my husband :)
Read less
Diane from Sumner, IA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken washer impeller
Removed and dismantled the pump assembly and found the impeller shaft was broken. Found the correct part number, ordered the part and it works like a charm. Assembly reverse of disassembly. Replaced the pump gasket and outer door panel(dent)as well. Great store!
i removed the bottom spindle inside of the washer compartment. laid the pieces out in order of which they were removed. found the impeller was busted where it attaches to the shaft of the motor. screw was missing but found it laying in the bottom (there is a screen that filters the water as it drains). replaced impeller and put parts back
... Read more together in order. good as new.
Read less
Matthew from maple shade, NJ
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No pressure in Spray Arms, no washing action
The hardes part was to remove the retaning nut (#34 on the diagram). There isn't enough grab on it and it is quite flimzy. Be prepared to butcher it if necessary. I resorted to wedging a screwdriver between the top flange of the nut and the spray arm and that gave me torque I needed to undo it. Luckily, the nut survived and could be reuse
... Read mored. Once the nut is off, everything else is pretty straightforward, just pay attention what goes after what and in what orientation (take notes if you must, however, I did not and got away with it). My machine has not been serviced in years and there was calcium deposits everywhere. If your machine is just as bad as mine, I strongly suggest to remove everything that can be removed and give it a nice vinegar bath or use other products designed for calcium removal (ask your wife what she is cleaning the bathroom with, it will most likely do). Bottom line, the cleaner the parts are, the better it will pump. In my case, it was the calcium that eventually killed the impeller #14 and made it spin on the shaft (no pumping therefore). Inspect all the parts for heat / wear damage so you put one order for everything you might need. Secondly, the screw #12 that holds the impeller #14 on the shaft is a tiny screw and it is originally secured with a threadlocker. Make sure that the internal thread in the shaft and the screw are absolutely dry before applying loctite. Thirdly, there is a plastic ball that sits in the cavity in one of the disk-like part (not shown on the diagram). Do not loose it and make sure it is put back. That's pretty much it. Once properly cleaned and repaired, the machine washed like brand new. Pretty good for less than $50 investment in parts and a week downtime. . .
would not wash or pump water out. Made noise like a bearing was out on motor. Went to dealer and was told that the motor and pump assy was not available because the washer was too old (18 years) and if a part was found it would cost $205. He wanted to sell me a new washer for $215. I went home
Removed the 6 screws holding the pump and motor assy. Disconnected the two hoses and wiring connector. Removed the motor and pump, removed the pump parts to get down to the impeller. Removed the old impeller (one screw) and installed the new impeller. Put every thing back together and it worked fine. Every one is happy!
Keith from Bloomington, MN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
4 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud grinding noise on rinse cycle, water not draining
Turned off the circuit breaker. Removed the two lower panels below the door. Removed the two racks from inside the tub. Removed the lower rinse arm, then unscrewed and removed in stages as much of the washer components from the inside bottom of the tub. Last item was the unit that screws into the base of the tub, was loose but would n
... Read moreot come out, then I realized I needed to disconnect the water lines from underneath the tub. Then I was able to lift the pump/motor assembly out from inside the tub. Disassembled that until I reached the wash impeller, and saw that the shaft was no longer rectangular, but rounded out and spinning freely which was why the water was not being pumped out. Also found a small flip top from a can, no idea how that got down there, but that was what was making the loud scraping noise as the was impeller tried to spin. Reassembled everything and unit now works fine (and much quieter!) Never had to take the dishwasher out from under the cabinet and if I had to do this again it would only take 30 - 40 minutes - live and learn!
I unscrewed the parts of the washing tower, then removed the housing and filters above the impeller. Lastly I removed and replaced the impeller and "o" ring. This repair went fine. Unfortunately another part (blower) let go and I decided not invest any more time or money into this machine since it was so old.
John from Yonkers, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
5 of 6 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kara
December 18, 2018
When removing the machines wash impeller a piece broke off and is stuck on the dishwasher. Any ideas on how to get it off. I have tried everything
For model number DWU8860
Hi Kara,
Thank you for your question. Depending on what piece broke off of the impeller, you may have to use pliers, a putty knife or a flat head screw driver to gently pry it loose. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Mimi
January 14, 2019
We tried taking it off with a putty knife, flat tip screwdriver while soaking the entire area with wd40 and let it sit overnight, and still unable to pry it off. In the process, a couple of small parts broke off. I think it was probably sealed on with a glue or some kind of adhesive because it just doesn't want to come off. We may have to snap it off and break it. What are the issues/problems of doing that other than getting a new part? Thank you for your prompt response.
Hello Mimi, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Mimi
January 14, 2019
We tried taking it off with a putty knife, flat tip screwdriver while soaking the entire area with wd40 and let it sit overnight, and still unable to pry it off. In the process, a couple of small parts broke off. I think it was probably sealed on with a glue or some kind of adhesive because it just doesn't want to come off. We may have to snap it off and break it. What are the issues/problems of doing that other than getting a new part? Thank you for your prompt response.
For model number DWU8460AAX
Hi Mimi, thank you for your question. It actually should not have been attached with any sort of adhesive. The only problem really with doing that is potentially breaking other parts. I hope that helps. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Leslie
October 4, 2019
We had standing water in our dishwasher. In our search to see if there is a blockage or structural problem, we are trying to remove the impeller. We removed the screw but it doesn't want to come off. Is there a trick to it or reason it would feel stuck? Thanks!
For model number DWU9961AAE
Good Day Leslie. Thank you for your question in regards to Part Number WP902461. Based on our research here are the instructions on how to remove the impeller: 1) Removed lower basket. 2) Lifted off spinning wash manifolds. 3) Removed 6 screws hold cover of wash strainer and removed strainer. 4) Removed 3 screws holding cover over impeller area. 5) Removed screw holding broken impeller. Hope this helps. Best Regards.
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
