Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
This is the replacement bellow clamp for your washer. It approximately 16 inches in diameter and is sold individually. The bellow clamp goes around the bellow in your washer and holds it in place on the washer frame. The main reason you would want to replace the bellow clamp is if it is rusted or damaged, and it is not holding the bellow into place. To remove the bellow clamp, simply use a screwdriver to pop the bellow clamp out of the groove it rests in. Place the new clamp back into the bellow groove until it snaps into place. This is an OEM part from the manufacturer.
How Buying OEM Parts Can Save You Time and Money
Why buy the real thing?
OEM stands for Original Equipment Manufacturer. Simply put, this means that the company who made your appliance is also supplying the replacement part for it.
I found a you tube video with step by step instructions. Very easy to follow. Repair would have been quicker had my kids not been at home. I had to have my boyfriend help me put on the outer bellow spring clamp, as I was not strong enough. Washer works great.
It takes 2 people to do this repair.The bellow is the hardest part. One person has to hold the bellow in one spot, and the other person has to put it on the rim of the drum all the way around. Sort of like putting a tire on a bicycle. Dont do what I did and pry the door open. If you do that you will have to get a new door lock control at
... Read more$54.Take off the lower front panel and reach up to the manual releace tab on the right side and pull down. Please make sure that the power is turned off, unplug the washer from the wall for your safety. The door switch itself is easy to replace, 3 screws, 3 plugs. Hope this helps.
Removed bellow clamp (used screwdriver to pry clamp open). Removed Bellow to Outer Tub Clamp with socket set. Removed Bellow. I had purchased new clamps as I didn't know condition of the old clamps. The Bellow to Outer Tub Clamp was in good condition, appeared to have an anodized finish - was not corroded and the tightening screw point
... Read moreed forward where as the new clamp appeared to be galvanized and the tightening screw paralled the clamp. I assumed the new orientation of the tightening screw was to make it easier to tighten with a screwdriver, but space is limited and I had good success removing the old clamp with a socket set so I elected to reuse the old clamp. Plus, I liked the finish of the old clamp better - it had zero corrosion on it after several years, almost a decade, of use. Reinstalling the bellow was the hardest part of the repair - it is just tedious and patience is required - I took a couple of breaks seating the Bellow to the outer tub. There was a tab on the Bellow which went to the top to insure the Bellow was properly aligned. After I seated the bead of the Bellow all the way around, I slipped the Bellow to Outer Tub Clamp over the Bellow and tightened it down - continually checking the seating of the Bellow. I then put the Bellow over the water inlet tube and seated the outer portion of the Bellow. I needed additional hands to help hold the outer clamp in place - my wife helped - and I used pliers and plastic pry wedges from a tire patch repair kit to pull it open and slip it over the Bellow - I didn't want to use screwdrives as I was afraid I would damage the Bellow.
I removed the outer tub clamp using two needle-nosed pliers. Then I folded the bellow back and removed the bellow from the dispensing outlet. I then losened the bellow clamp using a screw driver. It was on there very securely. Then I had my daughter with her smaller hands finish untightening the screw enough to release the bellows from th
... Read moree machine. Then the bellow and clamp were taken out of the machine carefully, not scratching anything and noting orientation for new bellow. I cleaned the machine surfaces. Next, lining up the top notch on the bellow, it was worked into the groove around the entire inner basket. The bellow also had to have the hole covering placed over the dispensing outlet. This was the most time consuming. Just to make certain that it was positioned correctly took 20 minutes. I then put the bellow clamp back on and tightened it to the very tight positioned it was in prior to being removed. My daughter returned to help with the smaller bellow clamp that goes to the front of the machine. I needed help keeping one side of the clamp in placed while the other side was stretched out again to go onto the bellow. Then the machine was leveled top to back, side to side, leg nuts tightened. Works quieter than ever.
Pliers, Screw drivers, Wrench (Adjustable), Wrench set
71 of 90 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jerry
December 16, 2021
I see the outer clamp for the bellows on my front load washer. Is there supposed to be an inner clamp on this model. I see from videos on replacing the bellows that there are two clamps, an inner and outer. On my washer I see only an outer clamp being used.
For model number GHW9150PW1
Hello Jerry, Thank you for the question. This model has two clamps. The Part #: PS11765855 and Part #: PS11744959. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
When my Maytag washer is in the spin cycle it make a loud noise. Even is a run a small balance wash. I have noticed little pieces of plastic in the drain and behind the rubber when I open the door. My washer and dry are 17 years old. Can it be fixed? Does it pay? Or should I buy new?
For model number MFW9700SQ
Hi Mitch, thank you for reaching out. Based on the description that you have provided, we would recommend checking the drive belt, part number PS11754067, as it is the most likely cause of this issue. Over time, the drive belt can dry out or burn out and start to crack. Eventually, a piece of the belt can break off, causing the belt to make a loud noise whenever the motor is running. To determine if the drive belt is broken, inspect the drive belt. If the drive belt is broken or damaged, you may need to replace it. We hope this solves your problem!
