Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
This surface burner switch, also known as an infinite switch, controls and regulates the heat output of the burners on a stovetop. The user simply adjusts the knob on the user interface panel, which in turn controls this switch. Made for various ranges, wall ovens and cooktops, this is a genuine OEM part that comes by itself, without any hardware like screws or nuts. This burner switch is an electrical component that you also handle directly, so it can become faulty leading to problems like your stovetop not heating enough, overheating or staying at a fixed heat. This burner switch is a vital component for your stovetop and if it presents any of those issues, it needs to be replaced immediately. A screwdriver, set of pliers and wiring diagram will be needed for the replacement and installation process, and you will need to remove your appliance from the wall outlet first. Remove the knobs from the control panel and then gain access to the underneath portion of it with your screwdriver and disconnect the switch. Remove the wires from the burner switch with a set of pliers and disconnect the securing screws holding the switch in place. Now, you can install the new switch and reassemble the panel, being mindful of wiring each connector to the appropriate wire.
How Buying OEM Parts Can Save You Time and Money
Why buy the real thing?
OEM stands for Original Equipment Manufacturer. Simply put, this means that the company who made your appliance is also supplying the replacement part for it.
Element will not heat | Will Not Start | Oven is too hot
This part works with the following products:
Range, Cooktop, Wall Oven.
Part# W11120791 replaces these:
AP6278040, 04100359, 04100360, 04100361, 04100426, 04100429, 04100502, 4381772, 5-70199, 570199, 7-3650, 703650, 7403P402-60, W10894483, WP7403P402-60, WP7403P402-60VP, Y04100359, Y04100360, Y04100361, Y04100426
...
Show more, Y04100429, Y04100502 Show less
Customer Reviews
Average Rating:
★★★★★
★★★★★
14 Reviews
3.9
Filter By Rating:
5 Stars
8
4 Stars
2
3 Stars
1
2 Stars
1
1 Star
2
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Cameron B - January 6, 2021
Verified Purchase
Fixed the stove, easy repair
The part arrived as expected and everything is working great.
★★★★★
★★★★★
John M - December 29, 2023
Verified Purchase
WORKED STOVETOP BACK UP AN WORKING -
Parts were in great shape - Delivery was fast received a few days after placing order.
Thank you
★★★★★
★★★★★
Gustavo B - March 8, 2021
Verified Purchase
Part Replaced Original Burner Switch
It would be helpful if a wiring diagram is included with the burner switch. Thanks.
★★★★★
★★★★★
Dan H - March 11, 2021
Verified Purchase
Perfect
The switch looks different than the original. And just plugged terminals to same letter designations and one had left over and plugged it to the only pin left and it works flawlessly.
★★★★★
★★★★★
John M - April 6, 2022
Verified Purchase
Thank you, PartSelect (and YouTube!)
The part was correct and the installation was fairly easy. Saved a much bigger repair bill, no doubt.
★★★★★
★★★★★
William D - May 14, 2021
Verified Purchase
Easy repair, but not the problem.
Quick delivery. Good part. Not the problem. Receptacle contact in back of stove broken.
★★★★★
★★★★★
Ronald R - January 16, 2022
Verified Purchase
worked great
wasn't exact but worked.
★★★★★
★★★★★
Sheila W - February 19, 2018
Verified Purchase
Love it!
The infinite switch fixed my problem! It was an easy install after watching the how to video!
★★★★★
★★★★★
Adrian M - October 21, 2020
Verified Purchase
Great part
Great part. Exactly what I was looking for.!
★★★★★
★★★★★
Freddy M - May 11, 2018
Verified Purchase
Almost an easy repair
Different configuration in the wiring from the old one, so it was a little tricky
< Prev
1
2
Next >
Customer Repair Stories
Average Repair Rating: 3.9 / 5.0, 55 reviews.
What's this?
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
worn out burner switch
easy enough. Before you start, draw a picture of where the wires go on the old switch ( or take a picture).
William from ARCADIA, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner control stopped functioning.
Replaced the control.
Kenneth from GAITHERSBURG, MD
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner had one temp. hot
Changed out surface burner switch.Unscrewed two screws, changed plug onto new switch.Don't forget to turn off power!
James from Charlotte, NC
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
both burner switches failed intrenally
simply remove and replace th switches using a screw driver an a pair of needle nose pliers
The 6in burner would go to max heat regardless of the setting.
Un screwed the two screws in the downdraft section enough to release the unit that holds the surface burner controls.Then removed the control nob, unscrewed the two screws that holds the switch in the unit, removed the wires, making sure the color of the wires were placed on the same contact point. Put it back together and it worked
... Read more>fine.Of course I did shut off the power before starting any of the above
Read less
James from Dunnellon, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
2 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burnt out oven element, faulty surface burner switch
As an arthritic 83 yr old I had a little trouble removing the two screws holding old element but with penetrating oil and channel locks on the screwdriver for leverage that problem was solved. Installation of new element was a snap, a matter of minutes to connect the element spades to the wire contacts and relace the two screws holding th
... Read moree element to the oven cabinet.
To remove the old switch I removed the four screws holding the control panel (Oven door must be open to get at screws)Removing the old switch took a few more minutes as with age of the unit the male spade contacts of the switch were tight on the female wire contacts and I carefully used needle nose pliers to free them. I quickly learned not to remove the two screws holding the switch to the panel until the switch spades were free from the female wire contacts. Installation of the new switch was easy. I replaced the panel with four screws, checked everything, reset the circuit breaker and I was back in business.
Replaced one of the four burner control switches on my Jennair cooktop. One of the tricks I use to prevent mistakes is putting the new switch along side the existing one and swap one connector at a time over to the new switch preventing any confusion and negating any need to mark the wires. This differs from your video assistant who disco
... Read morennected all the wires at once. gc.
Read less
George from Centreville, VA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner was not working & needed new grease filter
Parts arrived very quickly & the installation was quick & easy. Will order again.
Infinite switch malfuctioning and indicator light not working.
I changed out the infinite switch without any problems. The indicator light was another problem. It wasn't the light that was bad, it was the indicator light lens that snaps into the panel. The light then attaches to the lense. The lense broke and the indicator light pulled away with the tension on the wires. Now I have to order replaceme
... Read morent lens and will have a spare indicator light.
Ask our experts a question about this part and we'll get back to you as soon as possible!
22 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Vivian
April 16, 2018
My oven works, but the self cleaning process .Doesn't work. I don't know what part needs to be replaced. I set all the controls as shown in the manual. The door locks and the fans turn on but the oven doesn't heat . The door stays locked, and the fans continue to run, but nothing else happens. I think it may be the temp knob needs replacing. On the back, of the knob it looks like it might be damaged. (pushed in)
For model number S136
Hi Vivian,
Thank you for your question. There are three parts that you will want to check. The first thing you will want to take a look at are you temperature sensor and your bake element. It does sound like those parts are working in your appliance though. So the only other part that would be the issue would be your electronic control board. I would suggest testing the other two parts just in case. I hope that helps. Good luck with your repair.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Dennis
July 18, 2019
I got a replacement switch W11120791. I need a wiring diagram for this it was made by Whirlpool can you help?
For model number JES9860AAW
Hi Dennis,
Thank you for your question. There is a wiring diagram listed on our website. Here is a link to it, https://www.partselect.com/ModelSections.aspx?ModelID=262399&ModelNum=JES9860AAW&mfgModelNum=&ManufactureID=1&Selected=53278&Position=6&mfg=Maytag&Type=Range&Mark=6. If you do not find this helpful, you will need to contact Whirlpool. Their telephone number is 1-866-698-2538. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Debra
September 4, 2019
Will part # ps12347301 work on my stove
For model number S120
Hello Debra, thank you for your question. Yes, this switch, ps12347301, is compatible with your specific model number. Good luck with your repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Paul
August 13, 2021
Broil element comes on no matter what you select on touch pad. Oven is always too hot.
For model number SVE47600BC
Hi Paul,
Thank you for contacting us. If the broil element comes on no matter what function you select, the issue may be with the oven sensor. The oven temperature sensor is the part that monitors the oven temperature and signals the electronic control board to turn the elements on and off. Before removing this part from the oven and testing it with a multimeter for continuity, unplug the oven from the electrical outlet. To test the sensor, you will need to reference your owner’s manual to determine what the correct reading should be for your model, as this varies from model to model. To test it for continuity, use a multimeter on the Rx1 setting and touch the terminals with the probes. This test needs to be done with the sensor at room temperature to produce accurate results. If your test results do not meet the manufacturer’s guidelines, you need a replacement temperature sensor. If the sensor is fine, you will need to check the broil element, the electronic control board and the wiring between the parts to see which one is causing the issue. We hope this helps! If you have any questions, please let us know.
I replaced the oven sensor in our JennAir stove and the temperature control resumed and cooked to temperature for 2 weeks. Now the broiler element is coming back on again and overcooking our food. Do I replace the control board now?
For model number SVE47600BC
Hello Paul, Thank you for the question. This is normally an indication the Electronic Clock Control Board is defective and may need to be replaced. We hope this helps!
Good day, it appears that both burner elements on the left side do not heat? I tested the elements themselves for continuity and they seem to be okay. The power coming in to the cooktop is fine. When i test the other side (which has a grill) it shows proper power. The element power however is low (108 v) and inconsistent when i turn the elements on. Is it possible that both switches failed at the same time? Can i swap the cartridge to the other side to see if they in fact still work? Thank you!
For model number Jenn-Air C236W-C
Hello Nick and thank you for writing.
Yes, it is possible both failed and yes you can swap them. It is the same switch for both sides. We hope this helps. Please contact us anytime.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Ida
October 24, 2022
Does this fit Jenn-Air model JES9860AAB?
For model number Jenn-Air JES9860AAB
Hello Ida, thank you for contacting us. Yes, this part is compatible with your model. If you would like assistance placing an order, please contact customer service. Good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Gerry
November 21, 2019
Left side elements will not heat the surface hot light comes on but elements do not heat
For model number CDE8300
Hello Gerry,
Thank you for your question. Our sources suggest replacing the surface burner switch under part PS12347301 for your model. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Queeny
July 22, 2019
One of the burners malfunctioned (no heat, no light) . I switch out the knob but still can't turn burner on. Would replacing infinite switch cures problem?
For model number C-226
Hello Queeny, Thank you for the question. I suggest testing the element and the switch that controls the element with a multi meter to check for continuity. Replace the part that tests to be defective. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Michael
May 28, 2023
How do you test the Surface Burner Switch?
For model number SVE47100
Hi Michael, thank you for reaching out. To test the surface burner switch, set the multimeter range selection dial to the lowest setting for ohms of resistance. Identify the location of the switch input terminals typically labeled L1 and L2 as well as the output terminals typically labeled P, H1, and H2. Confirm the switch is in the off position. Contact the black meter lead to one of the switch input terminals and the red lead to the corresponding output terminal. If the meter display indicates close to zero ohms of resistance even when the switch is in the off position, the component has shorted. Repeat the test on the other input and output terminals to confirm whether or not a short is present and replace the switch. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
