Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
The flat style oven igniter kit is used in gas ovens and ranges. It is what provides the heat needed to open the gas valve, and it ignites fuel for the burner assembly. This part can be used for both bake and broil elements, and it can replace both short and long igniters. However, it cannot replace round style oven igniters. If your igniter glows for 90 seconds or more without igniting the burner, this means it is too weak to open the valve. The element in your igniter may have shorted it and it might not glow at all, or it might only glow orange or red. It needs to glow white hot; if it cannot get hot enough the gas will not be released from the safety valve and it will be impossible to light the burner in your oven. This kit includes the igniter, ceramic wire nuts, an insulation pad, a metal bracket, a variety of plug ends, and an instruction sheet. The body length is 3 3/4 inches, and the element inside is approximately 1 1/2 inches. This replacement part has an amperage range of 3.3 to 3.6. The element inside this igniter is extremely fragile, do not touch it. Before you start repairing your oven or range, make sure you have unplugged it and shut off the gas supply.
How Buying OEM Parts Can Save You Time and Money
Why buy the real thing?
OEM stands for Original Equipment Manufacturer. Simply put, this means that the company who made your appliance is also supplying the replacement part for it.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Dennis N - November 14, 2024
Verified Purchase
Good DIY Repair
This is the second time I have replaced this part. It is a simple straight forward repair most novice like myself can do.
★★★★★
★★★★★
Scott B - January 26, 2018
Verified Purchase
Done in 10 minutes
Exact fit
★★★★★
★★★★★
William H - June 9, 2021
Verified Purchase
fix the oven
came fast
★★★★★
★★★★★
Dawn W - October 6, 2018
Verified Purchase
Easy to install. My husband installed it.
Part came and everything was as expected on the order. Thank You.
★★★★★
★★★★★
Marilyn S - August 25, 2018
Verified Purchase
Best parts service
My part was shipped quickly and was in a card board box with everything needed for the job .My stove is up and working. I made pizza ??last night.The best part in my mind is the video that shows exactly how to do it and do it right.The man that does the video is great.
★★★★★
★★★★★
Brett E - November 23, 2021
Verified Purchase
Flat-style oven igniter kit
Extremely happy with this product. Works great and had it delivered in 2 days.
★★★★★
★★★★★
Evelyn D - September 9, 2021
Verified Purchase
Fixed my 35 yr old oven
The part arrived in good condition a few days after I ordered it. I was able to fix my 35 year old Maytag gas oven for a whole lot less than a new gas range would cost. It now preheats to the very high temperature that I want.
★★★★★
★★★★★
Emilio V - March 18, 2018
Verified Purchase
easy process
Part worked great. order/service was easy and quick
★★★★★
★★★★★
DON S - January 30, 2018
Verified Purchase
Easy Repair, Excellent Service.
Service person at PartSelect found me the correct repair item. Phone call less than 5 minutes. Installation took less than 10 minutes. Initial order placed Sunday 8pm, oven back in service Tuesday evening. No service call, I saved $150.
★★★★★
★★★★★
Steven F - January 30, 2018
Verified Purchase
Easy Repair - Went Smoothly
Ordered it, received it, installed it. No fuss no muss. Nuff said.
< Prev
1
2
3
Next >
Customer Repair Stories
Average Repair Rating: 3.9 / 5.0, 133 reviews.
What's this?
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Oven taking to long to preheat.
Accessed igniter removed 2screws holding it.unpluged igniter installed new one.
Isaac from LATHRUP VLG, MI
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The oven igniter came on but the gas valve never turned on.
1. remove oven door 2. remove racks and oven floor 3. remove oven burner 4. unhook igniter 5. install new igniter 6. tuck wiring back in as reinstalling burner 7. put in the insulation supplied in kit 8. install floor and racks. 9. install door. 10. test system 11. oven came on. SUCCESS
James from PEORIA, IL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Self tapping screws stripped out, one broke in mounting hole
Punched out broken screw. Drilled out damaged threads to same size as igniter mounting holes. I used nuts, bolts and lock washers to mount igniter. Would have been very easy if mounting screws had come out. Video very helpful.
Scott from FORT WORTH, TX
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven ignighter no longer works
Well Got the part within 3 days. Followed instructions to install it and it worked. One thing you need to add to your kit is replacement mounting screws (2 nuts and bolts). It turns out that the original burner because of its age, had a hard time unscrewing it. The screws were very tight and ended up stripped. I ended up using a Dremel t
... Read moreool to cut the screws off. By now the holes were a little bigger than original so I had to put it back together with a nut and bolt that would fit the small hole. But overall this was my first repair and I would definitely order from you again. Your site's part search and documentation with video clarified it wonderfully. Great service and site!
Barry
Read less
Barry from PORTERVILLE, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not ignite
Very easy, video helped tremendously
Dominick from CLARKS SUMMIT, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
OVEN WOULD NOT HEAT
TOOK OVEN BOTTOM APART AND LOSSENED OLD IGNITERTHEN WENT TO BACK OF OVEN TOOK BACK OFF DISCONETED OLD IGNITER PULLED THE NEW THUR AND CONNECTED PUT BACK ON THEN ATTACHED FROM THE FRONT PUT OVEN BACK TOGATHER THEN TURNED OVEN ON IT WORKED I DID IT MYSELF I AM 64 YEAR OLD WOMEN
Mary from MEADVILLE, PA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
igniter failed to ignite
Replaced the igniter by removing 2 screws, pulling on the wires to pull the connector in from the back thru the oval opening, screwing in the the new element, reconnecting the wires, pushing the connector back and that did it.
Gino from ARLETA, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No heat in oven
Checked igniter it glowed but never got hot enough to open gas valve. I switched igniter from broiler to oven and oven burner lit. Switched igniter back to broiler as wires were shorter than the oven igniter. Ordered part from number and picture comparison. It took about 20 minutes to get it installed and all stove parts back together.
Cynthia from AURORA, MN
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Wrench (Adjustable)
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The oven igniter would glow red but gas did not come on to light the burner.
I watched a repair video, unplugged the electric,turned off the gas valve and disconnected the gas line. removed the shelves and burner tray. removed 2 screws and unplugged the igniter. Replaced the igniter and put tray and racks in.Hooked up gas and plugged in the electrical plug. Job done....
Ernest from CINCINNATI, OH
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven igniter although lit up it failed to permit gas valve to open
ordered new replacement oven igniter kit and also felt it was a good opportunity to change the oven temperature sensor so also ordered short oven sensor kit. both parts fit as described as original replacements with very little work involved. oven worked properly good well done and a big saving on a service call repair or new range.
Ask our experts a question about this part and we'll get back to you as soon as possible!
32 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Diana
November 28, 2017
What's the difference between a 3412d024-26 and a 3412d024-09 oven burner?
Hi Diana,
Thank you for your question. It looks like the first part is not only grey in color but also larger than the second one. The second part is smaller and black in color. I hope that helps. Good luck with your repair.
11 people found this helpful.
Was this helpful?
Thank you for voting!
Arlene
November 5, 2017
My gas oven and broiler do not light. The burners work fine. Igniter problem?
For model number 31000PAW
Hi Arlene, Thank you for the question. This model number does not come with an igniter. You will need to replace the Burner Pilot. PartSelect Number PS11750349.The pilot stays lit all the time and, when the oven is turned on, the flame gets bigger and surrounds the thermocouple. When the thermocouple senses the required heat, the safety valve opens to let the gas flow to the oven burner tube where the pilot flame ignites the gas.Hope this helps!
Does this igniter part #ps1573892 have the plug on the end of the wire to plug into my oven?
For model number S31HK-92 DKX FV
Hi Steve, thank you for your question. Yes, looking at the photo there is a white plug on the end of this igniter. I hope that helps. Good luck with your repair.
6 people found this helpful.
Was this helpful?
Thank you for voting!
Pat
December 19, 2018
I cleaned the oven, not using the self cleaning but with vinegar and baking soda. I believe i got liquid down one of the vent holes. Oven sounds like its going to light but doesn't. There is no gas smell. Broiler works and top burners work. Serial number is 3628197uy . Igniter, but which one ?
For model number CHG9800BAM
Hello Pat, thank you for your question. The igniter for this unit is Part Number: PS1573892. The igniter must provide enough volts for the gas valve to open, so if the igniter is not functioning there will be no gas to the oven. We would recommend replacing the igniter first. I hope this helps!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Jerry
January 25, 2019
My burners work and broil in the oven works. Just doesn't work on bake? Lost heat last year and turned the bake mode on with my door open and never worked after that
For model number MGR5750ADW
Hello Jerry, Thank you for the question. I suggest testing or replacing the Igniter for the bake, Part Number: PS1573892. Thank you for your inquiry, good luck with this repair!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Clifford
February 12, 2019
This is a built in oven. Do i have to remove the oven to replace item number ps1573892 flat style oven igniter kit
For model number magic chef Model 90H-k4X
Hello Clifford, Thank you for contacting us. We do have an installation video on our website for this part. Please see below. https://www.partselect.com/PS1573892-Whirlpool-12400035-Flat-Style-Oven-Igniter-Kit.htm?SourceCode=3&SearchTerm=ps1573892#RepairVideo Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Chris
November 11, 2017
At times the oven will not come on and fault code f5 comes up on the touch control pad for this jenn air oven. Is there a part that needs to be updated? When it does come on heats normally
For model number WMG3020B
Hi Chris, Thank you for the question. The manufacturer uses this error or fault code to indicate a possible problem with either the touch pad or control board. You can try to remove the touch pad and board and clean the electrical ribbon and make sure they are plugged in securely to see if this fixes the issue.Unfortunately both these parts have been discontinued and are no longer made so they are not replaceable. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Clayton
November 1, 2017
The oven and the broiler and the oven lite does not lite. Is there a fuse or a breaker some where
For model number 34GN-3TKK
Hi Clayton,
Thank you for your inquiry. There are some parts that you will need to check to see which one is causing the issue. You will need to check the flat style oven igniter, the short oven sensor, the burner spark ignition switch and the electronic control board. I hope this helps. Thank you and have a great day!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Steve
February 28, 2018
The broiler igniter is pulling enough voltage to start the gas flow, but it doesn't light. Can it be such a fine line that it opens the valve to let the gas flow but not glowing hot enough to light the gas? (fyi if i smack the burner with the heavy end of a butter knife, it starts the Flame)
For model number 31HA-92KXS-EL
Hello Steve, thank you for your question. Yest the igniter is very sensitive and might be getting enough voltage to glow and open the valve but not light the gas. I would recommend replacing the Flat Style Oven Igniter Kit 12400035. Good luck with your repair!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Reem
December 24, 2017
Hello, can the oven ignitor be used on overseas ovens which use 220v?
Hello Reem, Thank you for the question. The ignitor only works on appliances with 120 volts./ Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
