Make sure you haven't got the discount earlier.
Gearcase 3360629
Rated by 6 customers
A Bit Difficult
More than 2 hours
Ratings submitted by customers like you who bought this part.
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
Gearcase Specifications
How Buying OEM Parts Can Save You Time and Money
Replacing your Whirlpool Washer Gearcase
-
5 Stars
-
4 Stars
-
3 Stars
-
2 Stars
-
1 Star
- < Prev
- 1
- Next >
- < Prev
- 1
- Next >
- < Prev
- 1
- Next >
I did consult the video for help on replacing the clutch spring.
Thank you for that bit.
I admit to taking too much apart, most of the cabinet back can be left alone.
Some of the plastic wire keepers/routers suffered, as well as the console hinges.
The ne ... Read more wly reassembled washer works without a hitch, and truely it took me about 4 hours over several days to dissamble and reassemble.
It is louder in the audible range than before, but very serviceale for another 20 years, saints willing.
-
Richard from JAMESTOWN, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:More than 2 hours
-
Aaron from Lake Mills, WI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Socket set
-
Troy from Storm Lake, IA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
For ease of removing and re-installing the motor it is best the machine lays on its back. This way the grommets and coupling can be easily aligned on the face-plate without having to manually support the weight of the motor. In the tub, unsnap two agitator caps. The inner one has no tabs to break so pry and pull on the "ears". Use 7/16" socket wrench with extension to unscrew the bolt holding agitator to gear shaft end. Assuming the motor and face-plate are still off, unscrew the three screws holding the gearcase in place and slide it out. Before installing the new clutch onto the new gear shaft, slide the plastic thrust spacer? (in kit but not shown in any instructions) down the shaft, observing which is the correct side. Check for correct clutch spring, as per instructions. Slide clutch, open side up, down the shaft. Instal wire retainer (this can be tricky) and circlip. if the brake assembly slid down while sliding out the gear shaft, squeeze its spring with a pipe wrench and push it back up (with rubber mallet). The clutch kit comes with a plastic pawl? which mounts under the brake and mates with the clutch. If the locating pins for the old part are broken off, drill them out of their holes so the new part fits snug. Insert the gear shaft up the brake sleeve into the agitator so their splines mate. Screw gear case to its mounts, agitator to shaft end (not too tight here) and snap on caps. Screw on face-plate, replace coupling on motor shaft (if req'd.), set motor on face-plate, aligning the coupling and checking the grommets fit in their holes. Instal motor holding clips (with screws), mount water pump with its holding clips, and wire harnesses. Stand up machine and replace enclosure, back panel and hoses.
Replacing the gearcase was easy. Because of space limitations, removing and replacing the enclosure, etc. was a b**** that took most of my time. And watch the lid doesn't fall on your fingers!
-
Francis from Ann Arbor, MI
-
Difficulty Level:Easy
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
There was one almost insurmountable problem, however. The three-pin cog that connects the new gear case to the rest of the washing machine was cha ... Read more nged.......the cross-section of each of the cogs was not round.....but teardrop shaped. I ordered the correct gear case, based upon the model number of the machine, but apparently somewhere down the years Whilrlpool must have changed the cog profile design.
So, the man who did the repair simply got out a metal mill file and filed down each of the cogs so that they were round. It wasn't perfect, but it worked.
-
John from Upper Montclair, NJ
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers, Wrench (Adjustable), Wrench set
-
david from Monroe, MI
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
- < Prev
- 1
- Next >
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- 2
- 3
- Next >
17 people found this helpful.
6 people found this helpful.
5 people found this helpful.
5 people found this helpful.
3 people found this helpful.
3 people found this helpful.
2 people found this helpful.
2 people found this helpful.
2 people found this helpful.
1 person found this helpful.
- < Prev
- 1
- 2
- 3
- Next >
Manufacturer Part Number: 3360629
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Item is not in stock and usually ships 10-15 business days from the time you place your order.
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.