Washer Leveling Spring 8316845

James from MILWAUKEE, WI
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set

5 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

tub tilted forward. Some fill water would miss the tub

Removed cabinet found tub spring had worn thru rear frame, spring was also almost worn thru. Checked suspension springs very very worn at mounting points.
Ordered needed parts. All in Stock. First bracket came the next day took 5 days to get the rest 1 part at a time.
Forgot to order suspension spring clips, order them next da ... Read more

Read less

Other Parts Used:

Washer Spring Outer Bracket

Craig from HOLDREGE, NE
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set, Wrench set

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Weak and broken springs on washing machine

Looked at the repair instructions on your web site and it made the repairs simple and easy.

Other Parts Used:

Washer Inner Cap Seal

Monty from OXON HILL, MD
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Washer tub goes out of balance in spin cycle.

Found leveling spring loose on bottom of washer, the sheet metal on bottom of cabinet ad rusted through. Drilled new hole in sheet metal and installed new leveling spring. Greased hole with blue marine grease so it will last another 40 years.

Dale from DOTHAN, AL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

not to bad if you watch the videos

Other Parts Used:

ERIC from GOODLETTSVLLE, TN
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench (Adjustable)

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Out of balance on spin cycle

Followed the videos on the website. But had to order parts twice because it wasn't the springs it was the plastic bushings the tub sits on that caused the wobble. No big deal though. All told it was still far less expansive than a new machine.

Other Parts Used:

Tom from LATROBE, PA
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)

8 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Acting like it was unbalanced

I thought I would find broken springs but everything looked good. Comments and video very helpful.I figured springs must be stretched or worn out ,so for the money I figured worth a try. Insallation went well, washingmachine runs like a new machine. Much better than spending money on a new one. Thanks

Other Parts Used:

Washer Tub Wear Pads (3 Pack)

Michael from Glenburn, ME
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench set

92 of 97 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

washer moving 3 ft during the spin cycle sounding like elephants running through the house

Removed back panel to remove tub from shell. Unscrewed the brackets holding the springs. Used screw driver to pop out pads with hammer onto screw driver. Cleaned out tub and put grease on springs where they attach to bracket. Replaced panel and ran machine to find a leak. Took machine apart again to find the knocking of the tub again ... Read more

Read less

Other Parts Used:

Lid Switch Assembly with Leads

Washer Tub Wear Pads (3 Pack)

Annie from Haines, OR
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set

28 of 36 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Machine rocking about like crazy on spin

Took some online research to figure out how to get the cabinet off. Once inside I fitted the wear pads which were a breeze to remove using a knife blade to pry them up and removing them using the screwdriver. The springs were replaced one by one using strong fingers. The machine went through the spin cycle without any rocking or self-des ... Read more

Read less

Other Parts Used: