Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
This part is used to start the dryer once you have selected a setting with the timer.
How Buying OEM Parts Can Save You Time and Money
Why buy the real thing?
OEM stands for Original Equipment Manufacturer. Simply put, this means that the company who made your appliance is also supplying the replacement part for it.
Average Repair Rating: 5.0 / 5.0, 2 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
switch burnt out
first you had to take back top panel off remove wires from switch turn old switch to the right pull it out then connect wires to new switch put switch back in screw back panel back on very easy 10 minutes tops thank you
paul from west keansburg, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
22 of 23 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer would make a sound when the button was pushed but no response from the unit
I read your suggested test to determine where the problem was that was making the machine not start. Got part . Took off back control panel. I put the part on as your instructions guided me . SUCCESS! I set the timer and pushed the button and the dryer began turning immediately.
Sally from Newport News, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
11 of 13 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
3 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mike
February 1, 2023
will this part fix the dryer not starting unless the door is open?
For model number ferb6600fs0
Hi Mike, thank you for contacting us. First, check the door switch, part number PS2330880. If that does not take care of the issue, we recommend checking the following parts: selector knob, part number PS2330885, thermal limiter, part number PS419402, and drive motor, part number PS418132. We look forward to hearing from you if you need assistance with placing an order through our 7-days-a-week customer service. We hope this helps!
Will the timer still cycle (rotate) even if the dryer is not running
For model number GLGR1042FS0
Hello Robert, Thank you for your inquiry. If your dryer continuously runs after the time is up, this points to a faulty dryer timer. You can test it with a multimeter, setting it to the RX1 setting and place the probes on the terminals, the ohm reading should be between 2000-3000 and if it is not, then the timer is faulty. Good luck with your repair.
Was this helpful?
Thank you for voting!
Stephen
March 20, 2025
Start button only works intermittently, if I fiddle with the timer knob the start button eventually works. Is this most likely the start button or the timer knob and is there are way I can test them to be sure? Thanks
For model number FER211AS2
Hi Stephen,
Thank you for your question. To verify if the issue is with the push-to-start-switch or the timer, you will need to test these parts for continuity with a multimeter on the Rx1 setting to see if they are operating normally. Before removing and checking these parts, unplug the dryer from the electrical outlet. When checking the push-to-start-switch, you should receive a reading of zero. When checking the timer, you should receive a reading between 2000-3000 ohms. If your readings for these parts are different, then you will need to replace them. We hope this helps!
