Whirlpool Microwave Circuit Boards and Touch Pads
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular Whirlpool Microwave Circuit Boards and Touch Pads
Your Price
$84.23
In Stock
Whirlpool Microwave Service Assembly
PartSelect Number PS16620391
Manufacturer Part Number W11552018
This control board is an authentic replacement part sourced directly from the manufacturer to ensure compatibility with your microwave. It has dimensions of 4 inches by 8.25 inches. The control board is responsible for controlling the various functions and features of the microwave such as the power levels and cooking times. If it is faulty, your microwave will likely be unresponsive when you try to input commands, it may be unable to start or complete heating cycles, or it may display error codes. Additionally, a burning smell coming from inside the microwave may be a sign of a faulty control board.
Fixes these symptoms
- Touchpad does not respond
- See more...
Installation Instructions
jerry from BRYAN, TX
The microwave magnet would start when the door closed w/o a keypad signal.
Unplugged the microvave, removed the phillips screw holding the right hand section of the microwave in place (Note: This screw is found by looking through a vent opening in the TOP of the microwave body.). Lifted up and out on the right hand section of the microwave. At this point the right hand section is completely unattached to the microwave body. Unplugged all of the polarized wiring harnesses and removed the screw holding the green wire to the board holder. Removed the screws holding the board to the right hand section and installed the new board. Reversed the procedure to put the microwave back together. Note: Look at and manipulate the keypad ribbon recepticle on the new board to see how to remove and reattach the ribbon, if needed.
Read more...
Your Price
$196.00
On Order
Whirlpool Microwave Inverter
PartSelect Number PS2342258
Manufacturer Part Number W10217711
The inverter acts like the brain for the microwave. It sends high voltage to the magnetron to produce heat.
Fixes these symptoms
- No heat
- See more...
Your Price
$95.01
In Stock
Whirlpool Microwave Electronic Control Board
PartSelect Number PS16620240
Manufacturer Part Number W11545876
Your Price
$276.61
In Stock
Whirlpool Microwave Electric Control Board
PartSelect Number PS12348595
Manufacturer Part Number W11179310
Experience the ideal solution for your Whirlpool wall oven with our state-of-the-art electronic control board. This genuine OEM Whirlpool part is designed to flawlessly manage all oven functions, including adjusting temperatures and controlling heating. Highly compatible, it works with select models of renowned brands like Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef. Be certain to make correct oven model verification before placing an order. Installation is simple but please ensure power safety measures are adhered to halting the house circuit or unplugging the oven and don the proper safety gear. The efficient design of this control board guarantees a seamless fit and an optimal performance.
Your Price
$120.23
In Stock
Whirlpool Microwave Led Display Board
2) Removed the four screws holding the extension kit to the microwave (easily visible on the front of the microwave) and removed the side panels (required sliding the panels up and off).
3) Removed the six screws holding the microwave to the cabinet (exposed after removing the extension kit)
4) Slide the microwave out and unplugged the cord from the outlet
5) Removed the screws that secured the front display panel to the microwave. These are located on the side of the microwave just behind the display panel. There are a total of 4 screws, 2 on each side. Additionally there was a clip holding the front panel on. We were able to press down to get it to release. NOTE: You will not be able to fully remove the panel as there are cables that run back to the board which is only reachable by removing the top panel
6) Removed the screws along the sides. back, and top to remove the top panel (there are 3 screws on each side and 2-3 in the back, there is only one screw on the top near the back right that holds the top to a part inside the microwave.
7) Peeled the top off of the microwave - there is a line of double sided tape that held the front of the top panel to the back of piece where the front display panel was mounted.
8) Carefully remove the existing LED Display Board. There is a single plastic clip that you have to very gently press back to slide the LED out. We were not careful enough and the clip broke. It did not hinder the replacement and even without the small plastic bit the LED board sat snuggly in its spot.
9) Trace the cable from the LED board back to the circuit board and unplug the cable. We pulled the cable out through the front of the microwave as the hole from the front display panel back to the board was just slightly too small to fit the board through.
10) The new LED panel arrived with extra boards attached to it. There were clear spots where the boards were perforated to easily snap off.
11) Thread the new cable from the front of the microwave through the hole and plug in where you removed the previous cable
12) Seat the LED Display Board in the slot.
13) Replace the top of the microwave and the associated screws (we used four small bowls to separate the screws for the top of the microwave, screws for the front of the microwave, screws for mounting the microwave, and screws for the expansion kit)
14) Reseat the front panel and replace screws
15) Plug microwave back in. (We took this opportunity to turn the breaker back on to test and make sure everything was working before we remounted the microwave)
16) Place microwave back in its mount and secure with mounting screws
17) Replace the extension kit if applicable and its associated screws. Read more...
PartSelect Number PS11748663
Manufacturer Part Number WPW10124269
Installation Instructions
Krystal from YORK, PA
The LED display on the microwave was no longer functional. Some lights still showed, but not enough to be able to tell the time or validate timer settings.
1) Identified the breaker that the microwave was connected to and turned it off.2) Removed the four screws holding the extension kit to the microwave (easily visible on the front of the microwave) and removed the side panels (required sliding the panels up and off).
3) Removed the six screws holding the microwave to the cabinet (exposed after removing the extension kit)
4) Slide the microwave out and unplugged the cord from the outlet
5) Removed the screws that secured the front display panel to the microwave. These are located on the side of the microwave just behind the display panel. There are a total of 4 screws, 2 on each side. Additionally there was a clip holding the front panel on. We were able to press down to get it to release. NOTE: You will not be able to fully remove the panel as there are cables that run back to the board which is only reachable by removing the top panel
6) Removed the screws along the sides. back, and top to remove the top panel (there are 3 screws on each side and 2-3 in the back, there is only one screw on the top near the back right that holds the top to a part inside the microwave.
7) Peeled the top off of the microwave - there is a line of double sided tape that held the front of the top panel to the back of piece where the front display panel was mounted.
8) Carefully remove the existing LED Display Board. There is a single plastic clip that you have to very gently press back to slide the LED out. We were not careful enough and the clip broke. It did not hinder the replacement and even without the small plastic bit the LED board sat snuggly in its spot.
9) Trace the cable from the LED board back to the circuit board and unplug the cable. We pulled the cable out through the front of the microwave as the hole from the front display panel back to the board was just slightly too small to fit the board through.
10) The new LED panel arrived with extra boards attached to it. There were clear spots where the boards were perforated to easily snap off.
11) Thread the new cable from the front of the microwave through the hole and plug in where you removed the previous cable
12) Seat the LED Display Board in the slot.
13) Replace the top of the microwave and the associated screws (we used four small bowls to separate the screws for the top of the microwave, screws for the front of the microwave, screws for mounting the microwave, and screws for the expansion kit)
14) Reseat the front panel and replace screws
15) Plug microwave back in. (We took this opportunity to turn the breaker back on to test and make sure everything was working before we remounted the microwave)
16) Place microwave back in its mount and secure with mounting screws
17) Replace the extension kit if applicable and its associated screws. Read more...
Your Price
$83.25
In Stock
Whirlpool Microwave Service Assembly
PartSelect Number PS16620227
Manufacturer Part Number W11544456
Introducing the Whirlpool ACU PCBA Service Assembly. This genuine OEM part is compatible with select models of many popular appliances, providing the reliability and quality you expect from the Whirlpool brand. This assembly is specially designed to ensure the optimal performance of your appliance. Please ensure your model number matches before ordering as parts may look identical yet have slight variations in size and shape. Trust in Whirlpool's promise of quality in all their certified parts. Enjoy the peace of mind knowing you've chosen a dependable and durable product from a trusted brand.
Your Price
$93.05
In Stock
Your Price
$146.83
In Stock
Your Price
$198.13
In Stock
Whirlpool Microwave Cntrl-elec
PartSelect Number PS11765745
Manufacturer Part Number W10891907
Enhance your Whirlpool wall oven performance with our user interface control board. This essential component is specifically designed for wall ovens, enabling you to accurately select the time and temperature settings. Prior to installation, ensure to shut off the house circuit breaker or disconnect the oven plug for safety precautions. To avoid injury during the process, we highly recommend wearing work gloves. Revel in the convenience of adjusted heat settings with this exclusive Whirlpool CNTRL-ELEC control board.
Your Price
$250.10
In Stock
Whirlpool Microwave Electric Control Board
PartSelect Number PS12584434
Manufacturer Part Number W11261167
Introducing the CNTRL-ELEC Control Board with power supply, a genuine OEM instance designed optimally for Whirlpool model wall ovens. This user-friendly control board serves as the manager of your oven's functionality, overseeing everything from heating to temperature regulation. Remember the importance of safety: prior to installing, switch off the house circuit breaker or unplug your oven and always wear work gloves to keep your hands protected. It is crucial to validate that your current part and this, are compatible before your purchase. Even if they look alike, their size and shape might be differing. This uniqueness in every part reinforces optimal performance and longevity of your Whirlpool appliance.
Related Whirlpool Microwave Parts
- All Whirlpool Microwave parts
- Whirlpool Microwave Brackets and Flanges
- Whirlpool Microwave Caps and Lids
- Whirlpool Microwave Doors
- Whirlpool Microwave Ducts and Vents
- Whirlpool Microwave Electronics
- Whirlpool Microwave Elements and Burners
- Whirlpool Microwave Fans and Blowers
- Whirlpool Microwave Filters
- Whirlpool Microwave Fuses
- Whirlpool Microwave Glass Tray and Supports
- Whirlpool Microwave Grates
- Whirlpool Microwave Grilles and Kickplates
- Whirlpool Microwave Handles
- Whirlpool Microwave Hardware
- Whirlpool Microwave Hinges
- Whirlpool Microwave Knobs
- Whirlpool Microwave Latches
- Whirlpool Microwave Lights and Bulbs
- Whirlpool Microwave Motors
- Whirlpool Microwave Panels
- Whirlpool Microwave Power Cords
- Whirlpool Microwave Racks
- Whirlpool Microwave Seals and Gaskets
- Whirlpool Microwave Sensors
- Whirlpool Microwave Springs and Shock Absorbers
- Whirlpool Microwave Switches
- Whirlpool Microwave Thermostats
- Whirlpool Microwave Transformers
- Whirlpool Microwave Trays and Shelves
- Whirlpool Microwave Trims
- Whirlpool Microwave Wire Plugs and Connectors