Amana Washer Dryer Combo Seals and Gaskets

Videos!

Your Price

$42.95

Amana Washer Dryer Combo Drum Seal W/adhesive

★★★★★

21 Reviews

PartSelect Number PS970088

Manufacturer Part Number 280114

This drum seal with a silicone rubber adhesive is used in dryers. This part seals the drum to make sure air does not escape from the dryer. If your dryer is making loud noises, is not producing enough heat, or no heat at all, or there are marks left on your clothes, replacing the seal on your dryer can solve the problem. The tools needed for this installation project are: 1/4 inch nut driver, Phillips screwdriver, small flat blade screwdriver, and putty knife. Remember to unplug your dryer from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for installation instructions.

Fixes these symptoms

Marks left on clothes
Noisy
See more...

Installation Instructions

Jerry from Everett, WA

Rear tub seal failure

I removed the top cover and then the back cover, released the belt tensioner and removed the drive belt. Then slid the tub out of the unit and onto the back dack. Sanded the remnents of the old seal off. Wiped the tub lip with laquer thinner and applied the "fast" drying glue supplied with the kit. Installed the seal and re-assembled the unit...works fine Read more...

Videos!

Your Price

$7.95

Amana Washer Dryer Combo Washer Centerpost Gasket

★★★★★

7 Reviews

PartSelect Number PS11723081

Manufacturer Part Number W10814296

This part may also be referred to as a main outer tub seal. This part prevents leaking from the bottom of the tub. The gasket is approximately 2 inches in diameter to the outer edge, black in color, and made of plastic material. To perform this repair, you will need to disconnect the power, drain hose, and the inlet hose. You will need to remove the entire outside cabinet to have access to the tub assembly. The tub will need to be removed entirely. This is a genuine part that is sourced directly from the manufacturer.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Dexter from Milwaukie, OR

Washer made a loud banging noise at end of spin cycle, leaked water and agitator seemed loose

After entering the model number of your appliance you will be taken to a page where all of the parts are displayed by sections. On that page about in the middle there is a heading called "Find Part By Symptom." I figured out from there which symptom the washer had and read what other people were saying and how they made the repairs. Basically I had three problem areas, Noise, Leaking and a problem with the agitator. I focused on the loud noise first and decided I needed to replace the clutch/brake assemblies. I found the clutch parts page and on that page there was a video on how to make this repair. This video is all you need to gain access to all moving parts located under the cabinet. Which ever part you are replacing, I recommend watching this video! After removing the console, back panel and cabinet then laying the machine on its back just as seen on the video, I had access to the water pump, motor, transmission and related clutch/brake parts. As it turned out I did not need the clutch/brake assembly but as a precaution and because the parts were cheap, I replaced the motor coupling, water pump and tub wear pads. I decided to replace the agitator assembly because of several worn parts associated with the dog ears/drive shaft ETC. I put the machine back upright and took off the top cap on the agitator, then there is an inner cap with seal that gives access to the 7/16" bolt you must remove to remove the agitator. However once the agitator was removed I noticed metal shavings and play in the shaft. I used a spanner wrench to remove the spanner nut. I removed the Plastic Tub Ring (has several clips around the outer tub), then removed the inner washer tub to replace the Drive Block. Replacing the Drive Block stopped the loud noise at the end of the spin cycle. Now just reverse the order to put the machine back together and your done. For my situation it was best to take the machine apart and decide which parts I needed before ordering to minimize errors. These machines are made very cheaply and are designed to brake at some point in time and it is very easy to determine which parts are worn because most are made of plastic. In this process I also noticed where my leaks (did I say Leaks) were coming from. There were two hose clamps installed improperly from the factory, so check all clamps, hoses ETC. and you should be good to go. Read more...

Videos!

Your Price

$10.45

Amana Washer Dryer Combo Washer Inner Cap Seal

★★★★★

11 Reviews

PartSelect Number PS11748108

Manufacturer Part Number WPW10072840

This is an inner cap seal, but may also be known as an O-ring, and it is a part for your washing machine. Some symptoms replacing this part will fix include: leaking from your appliance, uncontrollable shaking and moving, loud noise, pumps but will not spin, or if your appliance will not agitate. This model is off-black in color and 3 inches in diameter. You will find this part inside the agitator in the middle of your washing machine. It is recommended to wipe down the barrier before putting the new seal on.

Fixes these symptoms

Does not dispense fabric softener or detergent
Leaking
Spins slowly
See more...

Installation Instructions

Lennis from Jacksonville, NC

Would not agita.

It was a blessing that I ordered the kit, because I thought it only needed the rubber seal and the four dogs. But because the seal and dogs cost less than the shipping I decided to order the kit and its good I did because the nochage on the basket sleeve was broke off. The blessing is that the sleeve was in the kit, sp it took 5 sec to slip it on along with the rest of the kit, and after about 15 min my wife was back to work. Thanks for saving me time and money without this web site I would have bought another brand new washer, thanks. Lennis from NC. Read more...

Videos!

Your Price

$10.45

Amana Washer Dryer Combo Dryer Blower Housing Seal

★★★★★

4 Reviews

PartSelect Number PS11743810

Manufacturer Part Number WP697770

This part seals between the blower housing and the blower housing cover.

Fixes these symptoms

Noisy
See more...

Installation Instructions

Tammy from PINEVILLE, MO

wouldn't heat

watched videos on this site Read more...

Your Price

$10.45

Amana Washer Dryer Combo Washer Transmission Stem Seal

PartSelect Number PS11746747

Manufacturer Part Number WP8577376

Sold individually.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Bob from East Palestine, OH

The motor turned with loud noise ,but nothing else worked

I used "Emley's Cheap and Easy Repair" book to remove,install and reassemble the machine.
A lot of time was used to clean the filthy tub and basket.
While replacing the broken motor coupling I decided to replace some of the seals.
PartSelect got the ordered parts to me in a couple of days.
I wouldn't hesitate to do the job again. Read more...

Videos!

Your Price

$46.16

Amana Washer Dryer Combo Cylinder Felt Seal

★★★★★

9 Reviews

PartSelect Number PS11741917

Manufacturer Part Number WP37001132

This cylinder felt seal is used in dryers and is located between the back of the drum and the rear dryer panel. If your dryer is experiencing any of these symptoms, replacing the felt seal could solve your problem: squealing or banging noise, clothes are getting stuck between tub and felt pad, takes too long to dry, not heating enough or not heat at all, or does not tumble. The tools needed for this installation are a 5/16 nut driver and a putty knife. Make sure to unplug the dryer from the power source before beginning this project. Refer to the manual provided by the manufacturer for further instructions.

Fixes these symptoms

Marks left on clothes
Noisy
See more...

Installation Instructions

Tim from South Glens Falls, NY

The Felt Gasket between drum and door ripped, vent manifold from Dryer to fan and lint screen broken

I pulled the bottom panel and the door panel to replace the manifold and felt gasket around the drum. I removed old gasket very easily, it peeled right off. I use brake cleaning fluid (Spray Can from Auto Zone about $1.45) to remove old glue. Used spray contact cement (Elmer's about 4.50 at Ace) and sprayed the panel and gasket surfaces and let dry. I then applied a 2nd coat and let get "tacky" and installed the gasket. You will need an extra set of hands to hold the gasket in place while you stretch it over the the panel. The vent manifold is held in place with 3 phillips screws and was installed in about 10 minutes. The only gripe I had was in the Parts-Select illustrated breakdown they don't tell you the lint screen comes with the manifold assembly, so I bought one of them too. Now have an extra lint screen Read more...

Your Price

$10.45

Amana Washer Dryer Combo Washer Spin Pinion Seal

PartSelect Number PS11741857

Manufacturer Part Number WP356427

This seal is for the top of basket drive tube shaft.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Bob from East Palestine, OH

The motor turned with loud noise ,but nothing else worked

I used "Emley's Cheap and Easy Repair" book to remove,install and reassemble the machine.
A lot of time was used to clean the filthy tub and basket.
While replacing the broken motor coupling I decided to replace some of the seals.
PartSelect got the ordered parts to me in a couple of days.
I wouldn't hesitate to do the job again. Read more...

Videos!

Your Price

$10.45

Amana Washer Dryer Combo Dryer Seal Outlet Housing

★★★★★

1 Review

PartSelect Number PS11743812

Manufacturer Part Number WP697813

This lint chute seal, also known as a seal for outlet housing, is used for dryers. This part seals the lint chute to the blower housing in a dryer. It prevents air from leaking around the filter housing. If your seal is broken, damaged, or overused, it can allow lint to bypass the lint filter. In this case, replacing the seal can possibly solve the issues. The tool needed for this repair is a Phillips screwdriver. Refer to the manual provided by the manufacturer for further installation instructions and remember to unplug your dryer from the power source before beginning this repair project.

Installation Instructions

Dennis from PALM BCH GDNS, FL

Lint filter seal worn out

The part wasn’t for my machine. Unfortunaly I was not able to repair it. I was sent stripe of foam with an adhesive strip on the back. I needed a felt strip. Read more...