General Electric Washer Dryer Combo Motors
- Search your model number to find:
- Genuine OEM parts guaranteed to fit
- Free manuals and guides
- Repair instructions and videos
Popular General Electric Washer Dryer Combo Motors
Your Price
$20.95
In Stock
General Electric Washer Dryer Combo Washer Direct Drive Motor Coupling
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly. Read more...
PartSelect Number PS1485646
Manufacturer Part Number 285753A
This direct drive motor coupling (Direct Drive Washer Motor Coupling, Motor Coupling, Washer Motor Coupling, Coupling Kit) provides a cushioned connection between the transmission and the motor shaft. It attaches to the direct-drive transmission and the motor shaft. If this part is defective it will affect the agitator in your washer because of its direct connection with the motor. Your washer may not agitate, spin slowly, or not spin at all. The coupling must be replaced when there is no longer a consistent connection between the transmission and the motor shaft. The coupling can wear over time because of its location between two major parts of the dryer. It is subject to material fatigue over time from normal use, or breakage caused by frequent overloading. The part measures approximately 2 inches in diameter, and is constructed of plastic and metal. This model comes in black/white.
Fixes these symptoms
- Burning smell
- Leaking
- Noisy
- See more...
Installation Instructions
Jeff from Wayne, NJ
No movement from Basket & agitator
The job looked intimidating but turned out to be very easy.First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly. Read more...
General Electric Washer Dryer Combo Kit Washer Motor And Pulley Assembly
PartSelect Number PS12343555
Manufacturer Part Number WH49X27319
Suitable for GE washers, this Drive Motor Kit ensures optimal functioning of your appliance by driving the agitator or spin basket during the washing cycle. You'll find that it reliably spins the spin basket and handles the agitator in both tumbling and agitation modes. This kit may incorporate assorted components; hence we recommend referring to your parts diagram for an exhaustive list of included parts. Prior to installation, it's suggested to disconnect your washer for safety reasons; do remember to wear work gloves to shield your hands. Rest assured your washer will perform at its best with this Motor and Pulley Assembly kit. Enhance your washing machine?s performance and longevity with this efficient motor kit from GE.
General Electric Washer Dryer Combo Drive Motor & Pulley
PartSelect Number PS11699355
Manufacturer Part Number WE17X22217
Unleash the full power of your GE dryer with this highly efficient Drive Motor and Pulley. It's designed to ensure a consistent and smooth operation of your dryer drum. When replacing this motor, please be mindful to inspect for a non-operational door switch on gas dryers and a problematic thermal limiter device or door switch on electric dryers. The kit comes complete with a wiring harness, carefully encased in Styrofoam for protection, and an informative instruction sheet. Make the most out of your home appliances with quality parts from GE.
General Electric Washer Dryer Combo Kit Motor Drive And Pulley 27 Nv
PartSelect Number PS12343030
Manufacturer Part Number WE49X27320
Introducing the KIT MOTOR DRIVE AND PULLEY 27 from GE, specifically designed for optimal functionality in your laundry center. This key component plays a major role in your dryer operation, as it is responsible for turning the drive belt which, in turn, spins the dryer drum. Prior to installation, ensure your laundry center is unplugged for safety. It is also recommended to wear work gloves to protect your hands during installation. Trust in the reliable performance of this GE motor drive and pulley kit for your laundry center. Get the most out of your appliance with this high-quality piece, manufactured by GE for a reliable and smooth laundry experience.
General Electric Washer Dryer Combo Motor & Pulley
PartSelect Number PS11700890
Manufacturer Part Number WE17X22215
Enhance your dryer's performance with the GE Motor and Pulley. This essential component is responsible for turning both the drum belt and blower wheel. In doing so, it ensures the drum rotates efficiently while promoting optimal airflow within. Installation is a straightforward process, but remember to disconnect the power prior to beginning and don gloves to protect your hands. Place your trust in the quality of GE's engineering and keep your dryer running smoothly with this Motor and Pulley.
General Electric Washer Dryer Combo Motor Plate Nv
PartSelect Number PS12342907
Manufacturer Part Number WE03X27285
General Electric Washer Dryer Combo Kit Washer Motor And Pulley Assembly
PartSelect Number PS12343554
Manufacturer Part Number WH49X27318
General Electric Washer Dryer Combo Drive Motor
PartSelect Number PS10061527
Manufacturer Part Number WH49X20495
This top-quality GE Washer Drive Motor and Shield Kit plays a pivotal role in your laundry center's operations. It ensures efficient turning of the gear case shaft during the agitation cycle and rotates the spin basket during the spin cycle. Beyond functionality, the kit also includes a motor shield to defend the motor from damaging water exposure. A thorough set of instructions are provided with the kit for straightforward installation. Please ensure to disconnect the laundry center prior to installation and wear protective gloves for safety. This product is specifically designed for optimal performance with GE Washing Machine Tub M.
General Electric Washer Dryer Combo Strap Motor
PartSelect Number PS265873
Manufacturer Part Number WE13X200
General Electric Washer Dryer Combo Motor & Bracket Fan
PartSelect Number PS12743429
Manufacturer Part Number WE16X29944
Related General Electric Washer Dryer Combo Parts
- All General Electric Washer Dryer Combo parts
- General Electric Washer Dryer Combo Bearings
- General Electric Washer Dryer Combo Brackets and Flanges
- General Electric Washer Dryer Combo Caps and Lids
- General Electric Washer Dryer Combo Circuit Boards and Touch Pads
- General Electric Washer Dryer Combo Dispensers
- General Electric Washer Dryer Combo Drawers and Glides
- General Electric Washer Dryer Combo Drums and Tubs
- General Electric Washer Dryer Combo Elements and Burners
- General Electric Washer Dryer Combo Fuses
- General Electric Washer Dryer Combo Hardware
- General Electric Washer Dryer Combo Hinges
- General Electric Washer Dryer Combo Hoses and Tubes
- General Electric Washer Dryer Combo Knobs
- General Electric Washer Dryer Combo Latches
- General Electric Washer Dryer Combo Panels
- General Electric Washer Dryer Combo Pulleys
- General Electric Washer Dryer Combo Seals and Gaskets
- General Electric Washer Dryer Combo Sensors
- General Electric Washer Dryer Combo Springs and Shock Absorbers
- General Electric Washer Dryer Combo Switches
- General Electric Washer Dryer Combo Thermostats
- General Electric Washer Dryer Combo Valves
- General Electric Washer Dryer Combo Wire Plugs and Connectors