Gibson Dishwasher Parts
Popular Gibson Dishwasher Parts
Your Price
$35.34
In Stock
Gibson Dishwasher Lower Spray Arm
PartSelect Number PS12585623
Manufacturer Part Number 5304517203
The Lower Spray Arm is used in your dishwasher to spray water and clean your dishes. If broken there will be visible damage or your dishes may no longer be cleaned properly. If your spray arm is broken (due to general wear or high heat), it should be replaced. Your lower spray arm will be located at the bottom of your dishwasher tub. Check your user manual and model number to ensure this model is right for you. This version is plastic and metal and comes in gray/blue. We recommend you wear work gloves to keep your hands safe when installing and disconnect power to the appliance. You will also want to make sure that you turn off the water supply to your dishwasher. From here, you will want to open the dishwasher, pull out the lower rack and set it aside. Remove the lower wash arm. On each side of the bottom of the spray arm, there are small locking tabs that can be pushed aside using a flathead screwdriver. Once released, the spray arm can easily be pulled off the dishwasher. Put the new lower wash arm in place and push it down to lock it in. Ensure it is spinning freely and does not hit the heating element. Return the lower dish rack into place and then close the dishwasher door.
Fixes these symptoms
- Door latch failure
- Leaking
- Noisy
- See more...
Installation Instructions
Donna from Madison, OH
spray arm keeps melting
I have had to keep replacing the spray arm on the bottom of my dishwasher which takes like 2 seconds to do.. First you open the dishwasher and than pull the bottom basked forward and reach down and pull the spray arm up and pop the bottom of the spray arm off and put it on the new spray arm and slip it back into the dishwasher over the thing that makes it spin around.. but the tricky part is and I didn't know this and this is why my dishwasher spray arm kept falling over and melting on the heating element.. you have to turn it till it clicks in.. and your done..
Read more...
Your Price
$21.06
In Stock
Gibson Dishwasher Bottom Door Gasket
PartSelect Number PS9495545
Manufacturer Part Number 809006501
This dishwasher door gasket (Bottom Gasket, Gasket, Door Seal, Dishwasher Door Lower Seal) helps prevent water from leaking out of the bottom edge of your dishwasher door by creating a watertight seal. This part is attached to the bottom of your dishwasher inner door panel. It is frequently exposed to water and detergent during its lifetime. The water and chemicals can eventually wear down the gasket and compromise the integrity of the seal. If the gasket is malfunctioning, the integrity of the door seal will be effected. You will notice leaking through the bottom of your dishwasher door. If your dishwasher is leaking water from the bottom of the door, first inspect the seal for food particles near the bottom and sides, and remove the buildup, as it can stop the door from closing properly and keeping a tight seal; if not, you may need to replace the bottom door gasket. Check the door gasket for tears, cuts, or wear. This part is sold individually and measures 22.5 inches by 1.25 inches. It is constructed of plastic, and comes in yellow/grey. Includes one lower door gasket.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Leaking
- See more...
Installation Instructions
Scott from Flowood, MS
Bottom Door Seal fell apart and started leaking.
First I opened the door all the way. Second I reached down to the bottom gasket then grabed it on the right end of the seal that is on the right side of the door. Then I pulled the end outward from the bottom of the door toward the heater coil in the bottom of the washer. It came out real easy. You see it just snaps into a little plastic groove under the door. I then cleaned up the area for food and soap particules. I then placed the new gasket in place by lining up the notch toward the right end with the piece of plastic that encloses the right end of the plastic notch on the bottom right end of the door. Then push it in untill it stops going into the notch. It snaps in but does not make a snaping sound. It just won't go in no more.
Read more...
Your Price
$32.35
In Stock
Gibson Dishwasher Tub Gasket - Gray
PartSelect Number PS8260227
Manufacturer Part Number 154827601
This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing water leaking out. If broken, it should be replaced. Refer to your model number and user manual to ensure this part is right for you. When making this repair, open the dishwasher door and take out the lower dish tray for better access. Pull out the old gasket, and clean the channel with a rag. Push the new gasket into place into the notch on the door, which you should see upon close inspection, using a flat-head screwdriver for assistance if necessary. We do not recommend cutting any additional length off on the tub gasket if any is present during your repair.
Fixes these symptoms
- Door latch failure
- Door won’t close
- Leaking
- See more...
Installation Instructions
Charles from Milton, FL
dishwasher was leaking water
I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.
Read more...
Your Price
$6.88
In Stock
Gibson Dishwasher WHEEL & BUSHING ASS
PartSelect Number PS16745479
Manufacturer Part Number 5304532229
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, or you notice that your dishwasher is not cleaning dishes properly, you may need to replace the rack wheel. The single rack roller kit is made of white plastic, and clips to the dishwasher rack with the included axle/clip. Many of our customers have described this repair as easy, and you will not require any tools to complete it.
Lower rack roller and bracket assembly, grey. Wheel has been updated. If wheel pictured is not like old one, you may need to replace all wheels.
Fixes these symptoms
- Not cleaning dishes properly
- See more...
Installation Instructions
CHRIS from ROANOKE, VA
Water leaking from Inlet Valve
Remove the bottom cover plate. Disconnect the water inlet and black rubber hose. Remove 2 mounting screws. Pull out electrical connector. Reverse order. Be sure to get the brass inlet connector really tight so it won't leak. I did the final tightning after the part is mounted. Not a bad repair at all. The only problem was that it leaked in the first place and messed up my subfloor and laminate flooring.
Read more...
Your Price
$4.99
In Stock
Gibson Dishwasher WHEEL&BUSHING ASY, UPPER,BLACK
1. Removed stops on front end of Upper Dishrack Slide on both sides.
2. Removed Upper Dishrack
3. Remove Roller and Axle/clip (4 each)
4. Push Roller onto Axle on all 4 kits
5. Install all 4 roller kits on Upper Dishrack
6. Remove stops from back end of Upper Dishrack Slides.
7. Remove both Slides
8. Remove 8 each Tub Wheels.
9. Using old or new Screws and Washers, install new Tub Wheels.
10. Install both Upper Dishrack Slides ensuring that small holes are toward the back.
11. Install stops on the back end of Slides.
12 Install Upper Dishrackinto slides
13. Install front stops on slide
14. Pulled out Gasket
15. Install replaced Gasket Read more...
PartSelect Number PS17219660
Manufacturer Part Number 5304535381
The upper dishrack roller and axel kit comes with two pieces, a wheel and an axle. This kit is made for your dishwasher. Both pieces measure to be roughly one square inch each, they are made entirely of plastic, and are white in color. The purpose of these parts is to allow your dishrack to roll easily on the support rails. This kit is sold individually and contains only one wheel and one axle. Please order the required quantity for your repair. If your dishrack is having trouble rolling in and out you may need replace your rollers and axles.
Installation Instructions
Terry from Pleasant View, UT
Top rack was dropping out of rollers/Slides
This was the second part of repair. Left side was constantly falling out of the slide. I replaced the same items as above minus the gasket and screw kit. Once done, the right side was sloppy so I orders part for that side plus gasket which slid right in. 1. Removed stops on front end of Upper Dishrack Slide on both sides.
2. Removed Upper Dishrack
3. Remove Roller and Axle/clip (4 each)
4. Push Roller onto Axle on all 4 kits
5. Install all 4 roller kits on Upper Dishrack
6. Remove stops from back end of Upper Dishrack Slides.
7. Remove both Slides
8. Remove 8 each Tub Wheels.
9. Using old or new Screws and Washers, install new Tub Wheels.
10. Install both Upper Dishrack Slides ensuring that small holes are toward the back.
11. Install stops on the back end of Slides.
12 Install Upper Dishrackinto slides
13. Install front stops on slide
14. Pulled out Gasket
15. Install replaced Gasket Read more...
Your Price
$11.26
In Stock
Gibson Dishwasher Lower Spray Arm Support
PartSelect Number PS12712289
Manufacturer Part Number 5304518968
This lower spray arm is a genuine OEM part for various makes and models of dishwasher and is sold as an individual part. This part attaches to the lower spray assembly of your dishwasher and the lower spray arm itself clips into this part to facilitate its spinning movement during the washing cycle. To replace it, remove the spray arm by pulling it out, remove the surrounding circular clip and then twist to remove this bit. Made completely of plastic, this part measures approximately 3-inches deep, 2-inches wide, and 3.125-inches tall.
Fixes these symptoms
- Leaking
- Noisy
- Not cleaning dishes properly
- See more...
Installation Instructions
Dale from Worley, ID
spray arm fell off and melted on element
The Spray arm and the support had come off during operation and subsequently melted on the heating element. This was our fault, as a knife had slipped through the lower dish-rack and acted as a ramp to launch the spray arm as it came around. The support was a simple 1/4 turn counter-clockwise until it clicked into place, drop the strainer basket into position around the support, them push the spray arm into place until the catches snap over the retaining ring molded into the support. All told, about 10 minutes, max.
Read more...
Your Price
$26.66
In Stock
Gibson Dishwasher Drain Hose
PartSelect Number PS9494138
Manufacturer Part Number 807117001
If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in proper dishwasher drainage. This white and black plastic hose is 7.5 feet long. For this repair, you will need either a 1/4-inch or 5/16-inch nut driver, depending on your model. You will need to remove the lower access panel on your dishwasher to complete this repair; it is often easier to remove the dishwasher from the cabinet to do so. Be sure to disconnect the dishwasher from both the power and water supply before completing this repair.
Fixes these symptoms
- Leaking
- Not cleaning dishes properly
- Not draining
- See more...
Installation Instructions
John from Carthage, MO
Drain hose was missing
My friend bought a used dishwasher at a garage sale, the previous owner had thrown away the drain hose because it was "nasty" they said....remember it could have been cleaned. When I went to install it, I removed the old washer, and discovered that the old hose would not fit on the replacement dishwasher. I went to the local repair shop, armed with the model and serial #'s. they searched and searched their books and could not find the hose part number. they said "good luck" when I left...I went home and looked up the model on your web site, ordered the hose, and in 3 days had the dishwasher installed and running in about 30 minutes...thanks for prompt shipping.. I couldn't believe it arrived so soon...Mowerman
Read more...
Your Price
$232.22
In Stock
Gibson Dishwasher RACK ASSEMBLY,LOWER,GREY
PartSelect Number PS17219739
Manufacturer Part Number 5304535768
This grey lower dish rack assembly comes with eight light-gray rollers for easy access. The dish rack is approximately 21 inches wide x 22 inches deep. The dish rack holds dishes in place during the dishwashing cycle. If you see rust spots on the dishes, the lower rack will not pull out, or the lower rack is visibly rusted or damaged, you will need to replace the part. Other common symptoms include: unusual or loud noises coming from the unit, or the dishes on the lower rack not being washed properly.
Fixes these symptoms
- Not cleaning dishes properly
- See more...
Installation Instructions
Lauren from Monmouth, IL
Rusty racks
It was amazing, the items were shipped within days of placing the order. They arrived ready for installation. My husband had the new racks in place in 10 minutes. He removed the wheels from the old racks and placed the wheel on the new racks which required no tools. Then we slid the new racks into place, a perfect fit!
Read more...
Your Price
$21.60
In Stock
Gibson Dishwasher Filter
PartSelect Number PS11770489
Manufacturer Part Number 5304506525
This filter is for dishwashers.
The filter removes food particles and debris from the water to prevent the drain from clogging.
Follow the instructions in the manual when installing this part.
Fixes these symptoms
- Noisy
- Not cleaning dishes properly
- Not draining
- See more...
Installation Instructions
Denise from EUGENE, OR
Filters and drain trap extremely clogged, causing dishwasher not to drain and leak.
Removed old filters and trap and installed new ones.
Read more...
Your Price
$125.80
In Stock
Gibson Dishwasher RACK ASSEMBLY UPPER
PartSelect Number PS17219604
Manufacturer Part Number 5304535251
The upper dishrack is used to hold your dishes in place while the dishwasher goes through the wash cycles. Over time the dishrack can become damaged, start to rust, or be missing rollers, and the dishrack will need to be replaced. This rack is white in color with light gray rollers and measures approximately 23 Inch x 23 Inch. This is a genuine OEM part.
Fixes these symptoms
- Not cleaning dishes properly
- See more...
Installation Instructions
Lauren from Monmouth, IL
Rusty racks
It was amazing, the items were shipped within days of placing the order. They arrived ready for installation. My husband had the new racks in place in 10 minutes. He removed the wheels from the old racks and placed the wheel on the new racks which required no tools. Then we slid the new racks into place, a perfect fit!
Read more...
Gibson Dishwasher Appliance Types
- Gibson Air Conditioner Parts
- Gibson Cooktop Parts
- Gibson Dehumidifier Parts
- Gibson Dryer Parts
- Gibson Freezer Parts
- Gibson Microwave Parts
- Gibson Oven Parts
- Gibson Parts
- Gibson Range Parts
- Gibson Refrigerator Parts
- Gibson Trash Compactor Parts
- Gibson Vent Hood Parts
- Gibson Washer Dryer Combo Parts
- Gibson Washer Parts
Related Gibson Dishwasher Parts
Popular Gibson Dishwasher Models
Below are the most popular Gibson Dishwasher models we have. Enter your model number in the search box to find your model.
