10641123212 Kenmore Refrigerator - Instructions

I was not able to unplug the refrigerator because it is housed in a built-in. I removed the icemaker and following simple instructions from YouTube was able to pry the cover off the existing part. After a few gentle tugs, I disconnected the pinned wires from the old part. Connecting the new part was a little tricky but I managed with a little contorting. As soon as the pins connected the freezer light as well as the refrig lights came on. It took about 15 minutes to complete.

I removed the glides under the edges of the meat pan, remove the old pan, put the new pan in and replaced the glides. I was very pleased with PartSelect. I ordered my part, and it arrived the very next day. I will definitely order my next replacement part thru PartSelect.

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

I began by replacing the central light board by using a plastic non-marring wedge type tool slipping it between the housing and the retainers to release the latch like catch. Then I removed the lightboard and light cover assembly by depressing the latch like retainers for the two wire connectors. Installation was as simple as snapping the wires into the connectors and then pushing the lightboard and light cover assembly into place. One major note: I learned from a repairman that you cannot resolve the problem by simply replacing the central lightboard. you must replace all three lightboards, the two in the refrigerator and the one in the freezer because unless you can absolutely identify which board is causing the fault, it will continue to cause a problem on the main board and the lights will not work. Replacing the other two boards is the same as the central board. Additional comment to consider: I absolutely fail top see how this design of using three circuit boards for a simple light saves me anything; in fact after only 5 years it has cost me in excess of $400 (or 20% of the original cost of the unit) just in materials for a simple light--absurd, ridiculous design. If it burns out again I will have an appliance repairman install a simple 1950's design switch a small LED bulb which will probably last longer than the unit.

simply removed wires from the old motor and gently lifted it out by by the metal clips - put the old bracket on the new motor, snapped on the new fan, replaced the wires, reinstalled the shield. All done in about 15 min.

Same as everybody else on this post. Real easy. Actually, I just wish I would have done it sooner.

That was due to the evaporator blocked by the ice. Check found the defrost timer is okay. The next thing I can think of is to replace the Electronic Control Board which is installed in the fridge side top compartment. Ply open the face cover, remove the nut and screw that secure the EC Board. Pull out the cable, mount the new card and re-connect. So simple. It is back in order.

remove shelves in freezer compartment incl.holders(slide up to remove)
Remove lamp/shield
Remove panel (six phillips screws)
disconnect motor
pull off fan blade
squeeze bracket holding motor to remove
remove motor.
Re-assemble (in reverse)

New part slipped right into the studs and fit perfectly

From the time I started to finish I worked 3 hours, this included installing the new ice maker, cutting into the cold water line in the basement and installing a t with a 6inch piece of pipe with a compression valve to connect to the small cooper tube, this is worth your time to do it this way, its a lot better connection than the small pierce valves that come with the kit, they will leak over time. I installed the filter in the waterline in the basement for easy access

I tried to replace the light in the fridge first but couldn’t get it out (that one has the control board and is very expensive) so a replaced the one in the freezer by prying it off the ceiling. When I plugged the new one in all the other lights came on full power. Strange but I sent the other one back.

I originally ordered the led light control board but when I hooked it up I still had the same problem. My neighbor checked both door switches with a voltmeter and they were both good. I then ordered the light for the freezer and when hooked up the problem was solved. All lights worked. The freezer light has four tabs that allow it to snap into the roof of the freezer. Those tabs can be hard to see because there isn’t much room. I used a mirror to locate the tabs and a small flat tip screwdriver to push the tab over and removed the light.

Approximately:

1. Unplugged refrigerator.
2. Emptied Freezer.
3. Removed Ice Maker.
4. Waited a few hours for ice to melt around back panel & nuts.
5. Removed back panel and the cover over fan and fan motor.
6. Waited many more hours for ice to thaw over fins, wiring, etc.
7. Easily replaced the bi-mental defrost thermostat.
8. Replaced panel, fan cover, ice maker.
9. Plugged in refrigerator and waited a bit.

This worked! Yahoo.

p.s. I am a 65+ year old mechanically minded woman. :-)

Using a 1/4" nut driver and a philips screwdriver I removed all the screws in the shelf brackets and coil cover and removed coil cover. Removed fan blade and then faulty motor (held in with clips) Installed new motor-two wires (power) and ground (green) pushed fan blade back on and tested, then reinstalled all panels and shelf brackets.

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.