1064650049713 Kenmore Refrigerator - Instructions

1. Pull out drawer. 2. Remove screws to release the auger. 3. Unscrew the end of the auger. 4. Pull parts off. 5. Replace drum. 6. Replace parts in the correct order. 7. Twist end of auger back on. 8. Replace unit onto drawer and install mounting screws. 9. Place drawer in freezer. 10. Test ice dispenser. 11. Watch kitten run to refrigerator and beg for ice cube. 12. See smiles on family members faces.

Removed all ice from bin and let it thaw. Removed all screws and nuts from the front to release the ice crusher and the long bit. Had already printed out all the advice from others on the on-line section about taking photos and not getting the crusher blades out of order. Removed the clip with needle nose pliers and the washer. Removed the blades laying them down in exact order and direction they came off. Put on the new auger drum and reversed everything. It was nice to know that the plastic screw that held the clip is a reverse thread, otherwise we might have broken the dang thing. Too bad there aren't instructions with the part when you get it instead of just a diagram. All-in-all, it went well.

I could not have done it without reading the repair story about this same issue. I DID take a digital picture before taking the blades out and that was helpful. NO ONE, except in the repair story, ever mentioned the reverse screw to get the blades off. It simply made it possible for me.
I fixed it!!!! I am a 69 year old widow who loves crushed ice, so I am happy!!
The PartSelect service is great!

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

I was unable because you do not even carry the par that you still advertised on you sit and I was charged $20.00 to return the par. The representative was very rude and accused me of ordering the incorrect part as if I don't know the difference between a hose and a filter. When i expressed the poor customer service he disconnected the call. I will never patronize your business or recommend it to anyone.

Unplugged freezer turned off water removed 3 nut screws Unplugged old ice maker installed new ice maker

I followed the video exactly, pausing it as I went along. So unbelievably easy! And I’m 78 year old great -grandma! Thank you

I ordered two new ones from partselect.com. I figured if I was replacing the one for the refrigerator door I might as well do the freezer door too.
Very easy to take the old ones off, take the putty knife clean tracks out. Putting the new ones on, was a little harder to do. You have to start in the corner and push the gasket into the slot. You need strong hands to do this. Once I heard them click in, they guided themselves the rest of the way. Once they are on, check to make sure they touch the frame of the door. My freezer was perfect, but the refrigerator had an area of 25 inches that did not touch the frame. I called partselect.com and they sent out another new gasket for the refrigerator door. (I had to pay for this one but was told once I mailed in the defective one, they would credit me the cost of the returned one) I took off the bad gasket and installed the 2nd new gasket and that one was perfect.

Simply cut the water tube on both sides of connector and push in the new one.

The repair was super easy. It took all of 10 seconds. From ordering the part to repair, I would use part select 100%! Excellent company with excellent parts. Thank you!

Looked up on you tube to verify and see "secrets" to installation.

Changed inlet valve

First, I removed the 6 screws which hold the ice bin to the drum and the front cover. I then removed the screw which holds the door lever and bracket to the ice bin. Then I took the C clip and washer off the end of the auger to remove it from the housing. I removed the plastic nut to remove the auger drum from the auger shaft, being careful to place the blades on the table in the order they were removed. I then installed the new auger drum on the shaft and re-assembled everything in the reverse order. This was really easy for me because I had replaced the auger previously. (about 2 years ago)

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.