1064651773510 Kenmore Refrigerator - Instructions

Removed lower back cover of refrigerator; isolated water at wall, removed existing dual solenoid valve and installed new replacement valve assembly. Replaced back cover.

Unfortunately, this DID NOT correct the problem. Frustrated to spend that kind of money on something that was not needed.

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

Turned off power. Placed all frozen food in insulated containers. Removed all interior door parts to access ice maker, then removed the old ice maker. Dried everything with heat gun to make sure there were no ice obstructions. Installed new ice maker, interior door cover and ice bin. Turned on power, replaced food items shortly thereafter. It seems to be operating just fine.

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

1 Remove ice tray
2 turn off ice maker
3 Remove 4 screws
holding on the
cover over the ice
maker
4 remove the two hex
screws holding in
the ice maker.
Remove ice maker.
5 Reverse this procedure for installation.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

Remove back side cardboard access cover. About 6 dcrews need to be removed. Remove 9/16” bolt and lower compressor tray frame down to slide out wheel axel. Place wheel in slot and replace axel. Lift compressor tray and replace 9/16” bolt. Replace cardboard cover. Remove 2x4.

ONCE WE KNEW THE COMPRESSOR WAS NO LONGER FUNCTIONING , USED A MULTI METER TO VERIFY 120 VOLTAGE TO THE INVERTER WAS PRESENT, FOUND 120 VOLTAGE TO THE INVERTER WITH NO VOLTAGE TO THE COMPRESSOR. OHMS OUT THE COMPRESSOR, FOUND IT WAS WITH IN SPECS. REPLACED THE INVERTER AND ALL IS WELL ONCE AGAIN.

Removed freezer cover from ice maker, unplugged the harness. Installed the new ice maker assembly,plugged in two wire harness and secured the part and cover.
Results was smooth process, no noice from ice dispenser. Pleased with results. Saved on repairs. Thanks Tom

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

Very simple, easy, and quick! Anybody can do it!!

1 turned off the unit
2 removed the cover panel be removing 4 Phillips head screws
3 unplugged the on off switch attached to the cover panel
4 removed the two 1/4 in nut head screws holding the ice maker
5 removed the ice maker and disconnected the power at the join
6 performed the above steps in reverse
7 the unit has since been producing ice
Repair appears to be a success

pulled the top shelf and poped open the door and replaced the filter

This is an easy fix. The hardest part was just determining which part to replace. But the Q&A's for the ice maker from this site steered me right. And their video on how to install was easy to follow. The only difference I found was my Whirlpool had only 2 electrical connectors instead of the 3 in the video. I finished the job in about 15 minutes so everything in my freezer stayed solidly frozen.

After removing shelving and evaporator coil cover, suspended water bladder and evaporator coil with bungy cords. Removed and repaired drain pan, closing pitted holes and applying a coat of paint. Pushed evaporator fan WITH strofoam replacement to better insulate coil. Ensure that fan is facing up so that evap coil cold air is pushed up to top shelf area (mine came facing down). I used two digital thermometers, placing one on the top shelf and the other one the middle shelf to measure temp. Both read 37 degrees, which is fine.

Never did this particular repair before. Fairly easy.