106482394 Kenmore Ice Maker - Instructions

Removed Ice tray and flap followed by the three screws that held the old ice maker in place. (I probably didn't have to remove the top two, they are designed to just loosen and lift up on the mecanism to free.) I then pulled the old wiring harness out of the original ice maker. A small screw driver helped in depressing a tab while pulling on the harness. The same process was used to remove the wiring harness that was attached to the new replacement unit. I connected the original wiring harness that I had disconnected from the bad ice maker, and it fit perfectly into the replacement unit. No need to splice or use any of the harnesses that came with replacement. I tried installing the new unit and discovered that there was interfernce with the water feed hose. I had forgotten to break off the tab on the end of the replacement unit. Once I did that using pliers, the unit fit fine. I tightened the screws, installed the on/off mecanism and replaced the tray and flap. I then waited and waited, hoping to hear the forgotten sound of water entering the ice maker. Had a beer and walked the dogs thinking I had failed, but low and behold, over an hour later, the ice maker turned on the water. Many hours later, my wife woke me up in the middle of the night to declare we had cubes! Success.

I removed the 2 screws on top and the one screw underneath holding the Ice Maker to the wall of freezer.I pulled the electrical connection from the wall next (wiggled it back and forth until it came out).
I matched it up to the picture from this site and ordered the replacement unit.
When it arrived, it had a lot of extra parts to match up to mine and any other fridge.
A good tip is to keep the old unit so you can configure the new unit the same. Although it was easy, this took me the longest of the entire job. Once this was done, it took me !0 minutes to plug the new unit into my fridge and then attach it back to the wall with the 3 screws.Not a hard job.Thanks

I loosened the two screws on which the ice makers hangs and removed the third screw toward the back. I lifted the icemaker a bit and removed the part and unplugged the unit at rear. I reversed the process to install the new one. All very simple.

At first nothing happened, no water filling the tray. I thought there must be some other problem. A few hours later I heard ice being dumped into the ice container. I don't understand the delay but it works fine.



At first no

Just like the others. Unplug the refrigerator. Loosen the top two screw and remove the bottom screw. Unplug the unit, plug in the new one, slid the unit over the top two screws, replace the bottom screw and tighten the top two screws. Done. I ordered the unit Sunday it was shipped Monday and arrived Phoenix Wednesday, shipper then rerouted it to Tucson Thursday who sent it back to Phoenix on Friday and finallydelivered it Saturday.

Removed the old ice maker (2 screws, about 2 minutes). Read the excellent instructions. Prepped the replacement unit by adding the mount bracket. It plugged straight into the existing fridge wiring harness. Amazing how standardized icemakers are! Total time for a very careful job was under an hour.

It came in the mail, I got home about 5pm and had it installed that evening before dinner. First load of ice was in the catcher before I went to bed.

Very nice kit, and economical compared to a new fridge!

First I removed the (3) screws holding the unit to the side of freezer wall with a nutdriver. Then I disconnect the Harness from the back of the freezer. You have to work the Harness off connector because it was very tight. The Unit came with the correct harness installed so I reconnected the harness to the Freezer and replaced the (3) screws. I had ice in about 2.5 hours.

It actually took me longer to think about the repair than actually doing it. It was three screws, two upper that you just loosen and then one on the bottom that you remove. Pulled the unit out and disconnected the power. Slipped the new unit onto the two upper brackets, after connecting the power cord, tightened the bracket screws, reattached the bottom set screw and I was making ice. Incredibly easy. When I ordered the replacement unit they said it would arrive in 3-5 days, but it only took a day and a half. Great experience all the way through. I'm a customer for life.

First I removed the ice bin to give me room to work. Then I took out the screws that held the old ice maker in place. I disconnected the wiring. I then plugged the wires of the new ice maker into the old wiring harness. I put in the bottom screws and loosely connected the top screws. I checked the level of the ice maker with a small level and then tightened the screws. The nest thing was to install wire level that shuts off the ice maker when the bin is full. Finally put the ice bin back in place.

I replaced the old icemaker with a new one but the problem is still occurring in the new one. It only fill with enough water to make about two ice cubes

We followed the video on the KitchenAid website. We turned off water valve at the wall, unplugged the refrigerator, removed the old icemaker by unscrewing the three mounting screws. We unplugged old icemaker from electrical source at back of refrigerator freezer compartment and removed it. We detached the on/off bar from the old icemaker and installed it on the new icemaker. The new icemaker fit perfectly. We plugged in the electric wire to the existing power cord at the back of the refrigerator freezer compartment. We placed the new icemaker in the same position as the old, making sure the mounting screw holes were aligned. Plugged refrigerator back in and turned on the water. Works beautifully.

Ordered new ice maker from this site . Installation was very easy. Was happy to see that many electrical plugs were included. Chose the correct electrical plug and installed in 30 minutes. One note, be patient as it takes a while for ice maker to produce ice. When I heard the sound of ice dropping in the bin, I was very happy. Just in time for summer cold drinks. :)

I used a phillips screw driver, took the old one off, replaced the new one and it worked immediately!!! Didn't have to turn anything off...fixed in 5 minutes for $11. Fantastic Experience and my husband was shocked. No repairman bill.

The repair was very easy. I ordered the part from Part Seelect and the delivery was very quick.
Opened the box and took out the new ice maker. Emptied the freezer, turned off the power and the water to the Refigerator / Freezer / Iceww Maker. Used a quarter inch nut driver to remove the old ice make. Really easy remove one screw and lewsen two ther screws. unplugged the wiring harness. Took the bale arm off old unit and installed it on the new unit. Check to make sure I had the right wiring harness installed on the ic make which it was. Installed and leveled the new unit. in a little over a hour I had ice. Had to make a few adjustments to the water level setting to make sure all ice cube trays filled up completely.

So easy to do a cave man could do it.

First removed 3 screws and took out old ice maker, punched out water inlet tube area in new ice maker connected the electric and screwed it back in. Within an hour...heard the ice drop. (I did not do the repair, my boyfriend did, however I think I could have done it.

Looking at the instructions it looked like I had to rewire the the plug in the adapter. As it turns out, you don't .Using a screw driver, I released the braket mount and the nut driver loosened the nut holding the tray to the wall. It came right off when you lift it straight up and the wire assembly was exactly the same as the original. All I did was plug in the new ice maker, Hang the assembly on the loosen nuts and tighten again and put the screw back in the bottom bracket that held it in place. I spent longer looking at the instructions than I actually did in the whole replacement time. By morning we had a good amount of ice. EASY>>