1068265981 Kenmore Freezer - Instructions

Remove one 5/16 screw from top hinge cover plate. Trace outline of hinge on top of refrigerator with sharpie, so you will know where to put hinge back. Remove 3 5/16 screws from hinge. Lift door up out of bottom hinge, place on table to be able to work on. Remove one 5/16 screw and upper cam piece from bottom of door and replace with new upper cam piece. Remove one 5/16 screw and lower cam piece from bottom hinge on refrigerator. Replace with new lower cam piece and one screw Set door back in place and reattach top hinge with 3 screws adjust refrigerator door as needed for a nice even gap between freezer and refrigerator doors. Tighten screws down and put hinge cover back on with one screw.

Following the instructions on the site I removed the upper hinge cover and hinge(after removing the shelves from the door). I replaced both cams on the bottom hinge, reinstalled the door and the problem was solved. A couple of hints that may speed up the process: 1. On installing the door cam, I didn't get the holes in the door and cam aligned well due to a bit of interference from the metal tab on the door, so I temporarily inserted the upper hinge pivot in the bottom hole and retightened the cam. 2. I decide to re-align the freezer door . After this, the ice and water dispensers didn't work. Turns out the internal freezer light switch which also acts as a cutoff switch for the door dispensers wasn't being activated. Easy to adjust once the cause was discovered.

I did some tests and determined that the tub-to-pump drain hose had a leak in it.I then looked on the web to find disassembly instructions. I have a stacked washer dryer combination in a very confined space. The repair involved disconnecting both the washer and dryer from the water, gas, electric and venting systems first, then unstacking the dryer from the washer (not so easy, it required a helper). The machine was then pulled out so I could get at the parts necessary to remove the outside components and sheet metal. Then, I disassembled the top, front and access panel in the back. The disassembly went very well. I got access to the drain hose assembly and removed it fairly easily. I ordered a replacement drain hose assembly and found that installing the large port of the assembly was very difficult. (The two other ports were easy.) After thinking about it, I tilted the machine back a bit so I could try it from the bottom. That worked fine.I then reassembled and tested the machine. No leaks. Good luck with yours!

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

All I had to do was remove the screws at the top of the refrigerator door that hold the top hinge and once that was done I lifted up on the door and it came off. I then flipped the door upside down and was able to replace the door cam on the door and the other cam on the bottom hinge of the refrigerator. Once replaced, I put the door back on and put the screws back in on the top hinge of the refrigerator door. Works great now!

1, Removed heavy items from door bottom two shelves.
2. With door closed, prop up door with 2x4 boards and wood shim to support door weight.
3. With nut driver, wrench or socket wrench remove lower door hindge.
4. Removed worn plastic door cams and shim.
5. Install new door cams and shim.
6. Install lower door hindge and lubricate cams with silicone grease.
7. Remove wood bracing.

Removed the top hinge cap. Removed the 3 screws with a nutdriver. Lifted the door off of the bottom hinge and placed it on it's side. Then I removed both closing cams (one screw holding each). Clean the area then replaced each cam. I put some vaseline on the bottom cam and replaced the door. 4-5 minutes not counting removing and replacing the food inside the door shelves. I'm 56 years old and have always done most of my own handywork. I don't remember any job going so smooth and fast! Ever!

I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.

Replaced very easy.

replaced relay switch
when I finally got started to do the repair it took 15 minutes my biggest delay was no instructions were sent with the part and it took time to get some

removed screw on top cover emptied ref door remove 3 top screws holding bracket on top. lifted the door then remove old cam then reassembled.

Remove top henge, lift door off bottom henge, take off old plastic closer put on new one. Door works great now