11020172001 Kenmore Washer - Instructions

Job was easy! Just remove the top cap with a screw driver. With a socket and extension, remove the bolt that holds the agitator to the transmission shaft. Pull up on the agitator and lift it off the shaft. I had to use the screw driver to pry off the center piece that held the cogs because it did not what to separate from the rest of the agitator. Removed the pieces of the old, broken cogs, cleaned up the parts and installed the new cogs with the center piece upside down. I then took some silicone lubricant and lubed the area the cogs rub on and the opening the center piece spins in on the rest of the agitator. I then removed the Thrust Spacer on the mail part of the agitator but just lifting off the old one and putting on the new one. Then, with the center piece that holds the cogs upside down I inserted it into the upper corkscrew section of the agitator so that the cogs would not fall out. While holding the two pieces together, I turned it back right-side-up and installed it back onto the other part of the agitator and then on the shaft. Re-installed the bolt and tightened with the socket. That's it! It sounds more complicated then it really was.

The tub was out of alignment and water fell behind it and onto the floor. My brother-in-law suggested my problem could be the tub balancing spring and when I moved my washing machine, there it was on the ground.
The schematic does not show where it hooks up. So after I did what I thought looked right, the machine still did not work properly. Then I replaced the three suspension springs and that didn't solve the problem.
I found a whirlpool "do-it-yourself" repair book at the library and was prepared to tear into the machine. However, I did not have the tub balancing spring in the correct spot at one end. It hooks up from one of the outer bracket to the back of the housing unit along between the legs. There is a hole that had rusted through. I simply drilled a new hole nearby and low and behold it works!
Easy fix - the frustration was with the poor schematic.

First, I removed the softner cup from the top of the agitator. Second, I removed the plastic seal by pulling it out. I then used a socket to remove the bolt holding the agitator down. I then removed the agitiator from the machine and seperated the upper and lower agitator by placing my feet on the lower agitator and pulling up. The dog-ears were in the upper agitaotr section and easy to see and replace. I re-assembled in reverse order. The whole process took less than 30 minutes.

First, be sure to take the washer apart properly! The first time I fixed my washer I took it apart the hard way to change the clutch, and believe me it took longer to put it back together!
This time I was replacing both the water inlet valve and the hose leading to the disperser.
First remove the two screws holding down the control panel. It then flips back and hangs out of the way behind the washer. Then remove the spring-clip holding the rear plate to the body of the washer, one on each side under the control panel.
Next you need to remove the screws holding the body down to the base at the rear of the machine.
I then tipped the body of the washer forward and let it rest on a bucket so I didn't have to take it completely off. Then it is easy to access the hose and the water inlet valve. Shut off the water and remove the supply hoses to the washer. Remove the two screws holding the water inlet valve to the rear of the washer using a nut driver. Next remove the wires to teh inlet valve, making sure to note which one is cold and hot, and which orientation they are. Mine was yellow on top and brown on bottom. Next remove the springs clamps holding the hose on. Replace the hose re-using the same clamps. Replace the water inlet valve reverse the process to re-assemble the washer. Tilt the body back on, put the screws in the base, clamp the back to the body, flip the contorl panel back over and insert the screws. Reattach the water supply lines and you are done!

The repair itself was very simply, probably largely due to the design of the machine which made getting to, and replacing the two faulty parts a cinch. Just unscrew the two screws on the motor brackets which hold the motor down, and remove the brackets. Then remove the two smaller brackets which hold the pump to the motor. Then remove the two clamps and hoses from the pump. Lastly disconnect the power supply from the motor and the pump and motor will then come out as one unit. Simply reverse the process when reinstalling the new pump and motor. I used a bit of oil to lubricate the new motor shaft but I am sure it probably isn't necessary. The job should take no more than half an hour tops.

I'd noticed for a while that our 15-year-old Kenmore washer was filling slowly, but when it started to take 30 minutes to fill to the "medium" level, I knew something was really wrong. There was plenty of water pressure, so I replaced a hose that was loaded with minerals and cleaned the filter (also clogged with minerals). But that didn't help! So I ordered a new water inlet valve, and replaced that. There's nothing tricky about the repair -- the hardest part is opening and closing the washer, for which I found instructions online. (Even so, it's the most time-consuming part of the project.) The result is the washer now fills as fast as when it was new. Just for fun, I took apart the old valve and expected to find it encrusted with minerals, but it looked fine, so I'm not sure where the actual breakdown was. But since the part only cost $25 -- less than a service call, for sure -- I was very happy to use a half hour of my time and keep the machine going a while longer.

Unbalanced load was creating a knocking sound (as if the clothes load was unbalanced). Dismantled the washer to find that one brackets had rusted out. [FYI: 3 bracket at 120 degree apart (for the 360 degree circle)]. I found that the hole (on the bracket) where the spring holds was gone. Purchased parts. Replaced them (spring, bracket, screw). Reassembled washer then ran wash for a cycle. Successful fix.

This is a machine I bought from Costco in 2001 - it has been very reliable and this was its first repair.
Getting the top off this washer requires a lot of disassembly. However, if you push the drum down on the right hand side of the machine, you can easily reach under the lid and remove the old switch. Mine had broken loose from its plastic mounts, so the lid plunger no longer activated it. Save the two screws that go through the washer top to secure the new switch.
I unplugged the electricity, reached under the top and pulled the old switch out. Its cables are enclosed in a stiff plastic hose with a slit down its length so you can pull the wires through the slit. You need to pull out around 6 inches of the wires. I then cut the wires to remove the old switch and next cut the wires on the new switch to the same length as the ones removed. Stagger the cuts about 1 inch so that the two joints will not be on top of each other. I stripped each end of the two wires, slipped shrink-wrap tubing (from radio shack) on to the new switch wires, then soldered the new switch wires to the existing wires back to the control center. I then slipped the shrink wrap over the soldered joints and shrank it with a match. Feed the joined wires back into the plastic tube and feed the switch under the washing machine rim. It takes a little maneuvering to get the switch aligned with the two screw holes in the top. Be sure the switch is pushed up into the lip opposite the screw holes - push the back end of the switch up into the lip before trying to align the front end of the switch with the screw holes. Align the screw holes with the switch holes, install the two screws and check that you hear the slight click of the microswitch if you push down a pencil into the interlock slot before you tighten everything up. Plug in the electricity and off you go!

Unplugged power cord and disconnected water lines; note which is hot/cold. Washer was then tipped on its front. Discharge hose was disconnected. Washer was then rolled over onto its back as this would put the pump on top for much easier removal.

Pried off two clips attaching pump on motor using a flathead screwdriver. The rear clip was done by touch. Unplugged wiring plug from motor. Using an adjustable wrench (socket set would have worked better), remove two screws holding 2nd set of clips attaching motor on transmission. Then pried off clips.

Removed old coupling from transmission shaft and motor shaft, plus middle 6 hole widget thingy.

Installed new parts on transmission shaft and motor shaft with fingers pointing towards each other. Using a small hammer, tapped the parts onto each shaft. Placed 6 hole widget thingy on the transmission part, and then rotated motor so motor part would fit in remaining three holes.

Replaced clips to hold motor on transmission and reinstalled screws holding clips.

IMPORTANT: Replace motor wire now. I forgot to do this and after the tub was filled with water, realized that, and since the pump was also disconnected, could not get the water out. Had to get wife to hold washer up while I crawled underneath to reattach motor wire. Learn from my mistake!

Attach pump onto motor and replace clips. Double check everything is back in place.

Roll washer onto front side. Attach discharge hose. Tip washer back upright. Reconnect water. Reposition discharge hose and plug washer into power.

First try it smelled like something plastic was burning, but I think that was the old part shavings getting ground away.

Remove the main bolts that hold the gearbox in place, pull the gearbox and shaft out. You will see the brake shoes and drum--the large spring is a struggle to replace. Getting it out was not hard. The biggest struggle I had was replacing the brake shoe spring after replacing the shoes. I ultimately compressed the spring in a vise, then used safety wired it, then placed it between the shoes, then cut the wire to relaease the spring.

1) Unplugged electrical cord
2) Removed hot/cold water hoses
3) Took drain hose from laundry room recepatcle
4) Moved washing machine to area where I could lay it down on its back (very important for easy fix)
5) Found (easy accessible in my case) water pump with an inlet and outlet water hose held on with spring clamps.
6) Removed each of the two clamps with pliers and each hose by twisting loose
7) Remove two metal clips holding pump to motor housing
8) Slide pump off shaft - removal is finished!
9) Reversed process for installation, making sure to gently align pump housing when the pump is aligned with the shaft
[probably took less than 15 minutes]

Removed back panel to remove tub from shell. Unscrewed the brackets holding the springs. Used screw driver to pop out pads with hammer onto screw driver. Cleaned out tub and put grease on springs where they attach to bracket. Replaced panel and ran machine to find a leak. Took machine apart again to find the knocking of the tub against the back panel caused a whole in the plastic tub. Silicon and mechanical tape. Washer works fine for now.

I ordered the parts at a minimal cost compared to the repairman's quote, they arrived in 3 days. I used the laptop and put it right next to where I was working so that I could follow the directions step-by-step. The instructions were easy to follow and showed you right what to do so I never had any questions. My washer had a slightly different configuration but I figured it out. Replacing the parts was simple, take one off, put the other on. Putting the washer front back on was a little tricky, I had to have my daughter help me hold it in place while I wiggled it around to make sure it was just right before I screwed it back together. It was easier than I thought it would be. I told my husband I loved the internet, I would never have been able to do this job without the instructional video. Thanks PartsSelect!

Put the machine on its side. Remove old hoses and screw new ones into place. Done in under 20 minutes.

Three of the four agitator cogs had broken. The agitator was able to spin freely both clockwise encounter clockwise which it should not be doing. I replaced the cogs as well as a couple additional parts just to be sure but the cogs were the important one. Very easy.