25355333607 Kenmore Refrigerator - Instructions

After three years of cussing this 5-year old fridge for not ejecting the ice, and having to reach in and pull it out by hand, I fixed it with $100 and five minutes. Worse, I probably could have gotten Sears to honor the warranty and replace it when it first started acting up.

Repair could not have been easier. Loosened the two screws/fasteners with 1/4" drive socket set (straight-slot screwdriver wouldn't bite in the shallow slot). Do not remove screws completely; assy lifts up and off the screws for removal. Turn the unit slightly, unclip the electrical connector and remove. Installation is the reverse. Ensure assy sits flush on the screws to assure tray is level.

Although I probably could/should have unplugged the fridge first, I did not. I made sure the ice maker assy was off prior to installation to keep it from cycling on as I attached the ice maker electrical connector, which is before the remounting procedure.

Now it's making so much ice I have to find the plastic shelf cover for the ice bin to keep it from overflowing (which also helps move the ice level bar up to temporarily suspend ice production).

To access the part you have to remove the back panel of the freezer compartment from the inside of the freezer itself. There are four screws to this panel. I emptied the contents of the freezer, took of 2 shelves and brackets to gain access and removed the cover. Located the part , cut the wires with a wire cutter and left a small tail ....MAKE SURE TO UNPLUG REFRIG OF COURSE ... the part is clipped on the coils , added the new part. matched the color wires and added the connectors , crimped the wires and added a little electrical tape and put the panel and shelves back. THE REFRIG IS WORKING LIKE A CHARM

The repair was not my worry, but ordering the correct part. I was so pleased with this web site and the quick delivery of the part that I ordered. I easily found the bin I needed for my refrigerator and had the part at my doorstep with two days. I am extremely happy with this site.

After unsuccessfully trying to change the blown light bulb I discovered that the plastic light socket had gotten so hot that it melted and permanently fused with the blown bulb. After my new socket arrived in the mail I just popped the temp control assembly out with a screw driver and removed the old socket and placed the new one in. Whole operation to 5 minutes.

First I pulled the ice tray out so I could see the solenoid housing/ice tray support(1 unit). Below the ice tray there are 2 screws that hold the solenoid housing/ice tray support. After removing those the assembly lifts up so you can see the wiring harness to disconnect. I pulled it out and removed the 2 screws to open it up. There is 2 screws holding the solenoid in place and one ground wire. This was an easy fix and I know I saved a lot of money.

1.Unplugged appliance. Removed rear access panel, turned off water supply valve, removed two screws holding water valve assembly in place.
2. Removed and drained all water lines.
3. Removed three electric solenoid wiring connections.
4.Cut and marked all water lines to facilitate new connecting procedure (instructions provided with the new valve assembly).
5. Inserted the water lines into the new valve by applying a bit of vaseline on tubing end prior to pushing lines into O-ring fittings.
6. Clean the embarassing dust from under the appliance!!!

Note: All lines, wiring, and valves were color-coded to prevent connecting to wrong lines and electric solenoids.

Note: Be sure to remove water inlet supply trough to rear of ice-maker. This tube may freeze solid and prevent water from filling freeze tray. This is done by turning the inlet pipe on the back of the cabinet 1/4 turn and retracting from cabinet.

This occurred on Sunday and I ordered the part Sunday afternoon. By Tuesday afternoon the replacement was back at work. It just slipped into place, without any tools or fuss.

Reviewed the video on your website and followed the directions to the letter. Great video

This issue was noted in the advice area as being a filter, or valve assembly. But it turned out to be a diode kit that was causing this issue. I don't know why I could not find this issue anywhere on line? When I received the diode kit there was instructions that noted exactly the problem I was having.
The fix was easy just a few wires cut and spliced and viola fixed.

1. Remove outer plastic face cover (4) screws.

2. Revove (1) U type nut keeper & (1) metal washer.

3. Remove (1) plastic nut on end of metal auger.

4. Remove inner plastic cover (4) screws and disconnect control rod. (Note postion of control rod befor disconnecting)

5. Note position and order of metal blades and plastic spacers on auger before siding off the end of auger to reposition them upon re-assembly.

6. Remove metal support panel from end of ice bucket (4) screws.

7. Remove auger & plastic cylinder from ice bucket.

8. Remove - slide drive blade off auger.

9. Drive blade replaced.

10. Re-assembled other items removed in reverse order

I pulled out all the screws and from the freezer side and remove the panel, then I located the thermostat snap the old one out and put the new one in.

Really, really, really easy:
1.Unplug refrigerator (electrical safety).
2.Remove cardboard cover at bottom of refrigerator (two short self-tapping bolts) with a wrench.
3.Pull old fan blade off fan motor shaft (just held on by a compression fitting--no tools needed).
4.Push new fan blade on shaft.
5. Replace cardboard cover.
6. Plug in refrigerator, write nasty letter to Frigidaire.

This could not have been easier. I came to this website looking to see how much the part was before i called a repairman to come do it. I saw everyones instructions and decided to try it myself. To replace the ice maker you basically unscrew 2 screws, unplug the broken one and remove it. Plug in the new and tighten the screws to hold it in place. I would have been REALLY unhappy if i had called a repairman and saw that was how it was done.
Could not have been easier

pulled old gasket out of groove in door. Put vaseline on slotted part of gasket that fits in groove of refri. door Put some vaseline on gasket surface that would be on the hinge side of door, so it would close with ease. Had no problems at all. Thanks

P.S. Sorry about not having the model No.
The Part No was PS1991324 Magnetic Gasket for Refr side of a Freezer/Refrigerator FRIGIDAIRE There are no screws to remove on this model. Just start at one corner and begin pulling old gasket out of the groove of the door.

First I would like to say shame on electrolux for making me buy a $55 drawer rail for a 25 cent part. I will not buy another electrolux appliance. Repair is eazy, this was the meat tray. I removed the glass shelf inert and then tilted out the entire drawer/shelf assembly. Ithen pushed down on the drawer holder that was not broken to separate the drawer from the rail. The old part slipped backwards and out of the shelf and the new one slid right back in the same place. I then pushed the drawer onto both front retainers, reinserted the assembly into the fridge, replaced the glass shelf and was done. Very very easy. That must mean that this is a high failur part.