3638698586 Kenmore Refrigerator - Instructions

Piece of cake and now I get loads of ice.

Followed the instructions. Smooth as silk. This part is better than the original. There appears to be a sensor that beeps when the ice reservoir is full.

I spent 15 - 20 minutes just hunting/deciding which of several sets of parts & directions to follow. The provided directions were not bad; but none of them quite matched my GE ADORA side-by-side model. Once I came up with the actions I would need to take...I was done in 5 minutes! The kit , as I said, came with all the parts one could need (and one or two un-needed parts included for other model GE refrigerators) I am very happy with PART SELECT...altough GE doesn't rate as high with me for their declining reliability.

i watched the free video and then made the switch my ice screw had 4 bolts instead of three that was the only difference used the screw driver to loosen the straps on the connection plug and that was it easy as pie in about 30 minutes i heard it drop a load of ice it beats filling ice trays all the time thank you partselect for the free video it was the difference in my sucess

Soaked the new gasket in warm/hot water and snapped it on without any hassels. Thank you also for the fast delivery!

unscrew one screw unplug.insert the ice maker,put the screw back in you have ice less than ten minutes

Ice maker was side mount instead of rear mount as shown in previous insructions. Removed one screw and slide ice maker forward. used flat head screw driver to undo the ice maker plug. The ice maker came right out. Removed old ice maker fill cup and put it on the new ice maker. Slide the new ice maker into place and used the same screw to secure it. Pluged it in and turned on the ice maker. Had new ice in a couple of hours. It comes with a round plug to square plug adapter, new fill cup and fill tube, all of which I didn't use.

Only needed to remove one screw, slide unit out and disconnect the power cord. Theb reverse the above operation to install the replace ice maker unit. Quick and extremely easy....

took 1 screw out and removed ice maker and slid new one in and replace screw and connected power cord

We bought the side door retainer strip with the hope we could simply cut it to length and it would be the solution for the top/bottom retainer strip not available.. The problem was the holes for the flathead screws on the door bottom do not match the pattern of the holes on the side retainer. This meant we had to mark and drill new holes carefully on a drill press and then cut the piece to fit. After that it was no problem at all to screw it back to door and install the new gasket. Sure wish the top/bottom retainer strips were in stock somewhere.

My experience with PartSelect was excellent. My main concern was ordering the right gasket. First, I found the model number on the inside of the refrigerator. I ran model number on PartSelect and the compatible gasket came up. I removed old gasket carefully pulling it out. I cleaned around the groove that holds the gasket in and where the gasket lays. I boiled water and put it in a cake pan. I warmed up the gasket and smoothed and straighten it out. I started in each corner of the gasket and then worked from each corner pushing it carefully into the holding groove. Took me about 25-30 minutes. It seems to be working great!

I am more than 80 yrs, always thought I could fix just about everything--but, this looked complicated. Once I received the new icemaker; took a good look where the screw-holes, etc. were, then removed the "old" one. Took about 20 or 30 minutes, then the "new" one was easily installed.

Followed the video, very simple

I took off the front cover of the icemaker assembly and found that the gears were not meshing properly and therefore slipping. I removed the front panel and found that the white plastic cam unit under the large gear wheel had disengaged from the hole in the front plate which is why the gears were slipping. I refitted the cam and wheel and it worked fine but stopped again for the same reason the next day. As the plate appeared to be buckled somehow (not user repairable) and, as the unit was leaking and pooling water (which froze) in the collection unit, I decided to change the whole icemaker.

Ordered about 1300 on a Thursday, it arrived the next day at noon and was fitted straight away. As others have mentioned, the extension cable required to fit into my old fridge made it quite cumbersome however with a bit of juggling and persuasion, I got it to fit into the cut out corner of the ice container so it is completely out of the way. Job done in about 35 minutes, making ice in an hour.

The video on the GE site was great. Showed step by step instructions on how to remove the old ice maker and install the new one. Also helpful was the detail on the water chute which needed to be moved from the old ice make to the new one. Saved hundreds of dollars by not having to have a repairman do this work for me.