40448 LG Washer - Instructions

Found this part online. I just sets inside, did not click in like the bleach and fabric softener inserts. Think is ok, seems to work

The repair went good but time consuming. I replaced both inner and outer tub bearings along with the tub seal. I removed top by removing two screws in back then pulling back slighty then lifting up. I removed soap tray by pressing down tab and pulling out. Loosened soap dispenser and folded back on top. I removed control panel then front door panel. Remove back panel. Remove motor and shocks and hanging springs which there are two. Disconnect the hoses attached to tub then pull the tub. Remove screws holding the tub halves together. Use punch to remove bearings. NOTE: If you put the bearings in the freezer prior to installing, they go in much easier. I used the old bearing, set it on the new bearing then I tapped the old bearing so not to damage new bearings. I replaced the seal then put everything back together. Not difficult but time consuming.

I removed the tub. Thin included disassembling the washer and disconnecting various hoses electrical connectors to facilitate the removal of the tub from the machine.
Once removed, I separated the two halves of the tub and removed the metal basket to gain access to the bearings and seal.
Removal of the bearings was much harder than expected as they were very difficult to drive out of their pressed in mounting.
I finally was able to remove the bearings and fabricated a press using a piece of all thread and two steel plates to install the new bearings and seal.
I would not attempt to do this again with the proper bearing pullers and an official press to install the bearings gently without beating the tub housing.
This repair I feel is beyond the scope of your average DIY. The bearings can be damaged easily without the specialized tools to install the components.

When to utube typed in my problem, very easy fix

Entire machine must come apart to replace part. You tube installation instructions. They said at least a 3-4 hour job. Took me 4. I could see this repair costing at least 800.00 Would be worth buying a new machine but doing it yourself cost 225.00 and your labor

Water would fill the basin when the washer wasn't used. I followed the video created by this site to make the repair. The video gave me the confidence that I could successfully make the repair myself. The hardest part was physically moving my washer out of its corner to make the repair. The parts were plug and play. Awesome!!

I removed the top of the washer, pried the front control panel off (pull a couple of electrical connecters or just rest it on something), separated the tub sleeve from the front panel and then removed the front panel (two screws). To remove the pump - just remove a couple of hoses, two wires and slide it out of the clip below. Reverse the process to install. A little daunting if you haven't done something like this before, but easily do-able once you get past your fears. A service call would cost much more than the $60.00 it took to get the part to my front door. This worked out really great - my wash smells fresh once again and my wife has moved on to the next project on her honey-do list!

I followed the video on the PartSelect web site for this repair and it went just fine. I also replaced the drain hose while I had everything apart. Thank you PartSelect, same day shipping. Arrived within 3 day's and your video was spot on.

Followed the video instructions provided.

Viewed two (2) on-line video's for bearing replacement. Produced a 40 item "punch list" as to action to perform following video. Followed sequencing of video's. Noted a 10mm and 17 mm socket needed, used 3/8 drive sockets. Also noted that a "deep Socket" of unspecified size used to aid in removal of nylon pins attaching (3) shock absorbers. Found that 1/2 inch sized (SAE) socket in my 1/2 inch drive socket set fit in the confined space nicely. Did not need the "deep sockets" (3 plus inch overall length) rather a normal sized 1/2 drive socket worked nicely to depress the nylon pin retainers. During reassemble replaced outer tub gasket, checked bolt torque six (6) times over 45 min. to assure complete seating.

I BROUGHT UP THE YOUTUBE REPAIR VIDEO AND FOLLOWED IT STEP BY STEP AND WORKED OUT GREAT THANKS

Remove old one and replace. Just make sure it is all the way on and secure or you will have a huge mess on your hands.

Some screws, some clamps. Easy and straight forward. unplug machine, turn off water, disconnect water hose, unscrew top of machine (2 philips head screws), disconnect clamp from valve (use a towel for remaining water), disconnect wire, unscrew from place holder, remove entire valve, work backwards from there.

Hardest part was getting the correct part. Due to some glitch somewhere there was a mix up in the database for the correct pump number. This unit has two pumps mounted to the same housing. One is a recirculating pump and one is discharge pump. I ordered the discharge pump and kept receiving the recirculating pump. Discharge pump is LG PART#4681EA2001T and recirculating pump is LG PART #4681EA2002H Once in hand the install went fairly smoothly. Removed top - two screws on back of unit. Removed control panel with one screw on upper right inside corner, associated plugs and snap clips. Removed soap tray and drained water through filter tube. Removed screws in front of filter. Using Vise grips stretched spring from around front seal. Removed screws holding front of washer to top frame (2?)[accessed after soap tray removal]. Pump assembly located in bottom left, removed associated hoses, Marked wired colors on pump housings and removed. Removed assembly. Unscrewed pump, installed new pump and reversed procedure to reassemble. Struggled mostly with replacing spring around front seal. Stretch it as far apart as you can as you "roll" the spring in and then massage the seal to get the spring into correct position. Definitely a doable repair. Good Luck.

Removed the old bellows (2 squeeze hose clamps and one screw adjustable hose clamp) slid on the new one and it was done!