41182 LG Washer - Instructions

Just aligned and pushed in.

I followed the steps outlined on (several) web sites detailing the replacement process. Just Google " LG front load washer won't drain". A couple of small quirks cropped up that required some adaptations such as: I had to purchase an automotive hose clamp to reinstall the main tub drain hose to the pump manifold. I couldn't get the oem clamp back on. It kept slipping out to the jaws of my pliers and I don't own a pair of those clamp pliers that make the job easy. Also, the hex head/phillips screws used to attach the front panel to the frame were very tightly installed AND they had their heads rounded off! I didn't have the hand strength to make the phillips screwdriver loosen them so I used a pair of vise grips to carefully start the process and used the phillips to finish. Finally, the wire loop used to retain the big gasket that seals the front had door is tricky to reinstall. It took two people to get it right. All in all , the videos make the job pretty routine.

Pulled out the old plunger and inserted new one. Just have to make sure the tabs align with the slots.

Watched instructional video. Made it easy

Unplug the washer! Turn off the HOT water valve. Remove the hot water hose at the connection on the back of the washer. Remove the two Phillips head screws holding the top of the washer. Slide the lid toward the rear until you feel it disengage, then lift it off, setting it aside.
Unplug the electrical connector on top of the hot water valve (just pulls off).using pliers compress the hose clamp, slide it away from the hot water valve and pull the hose off the valve fitting(it will have some water remaining so lift it up and secure it to the brace above the hoses).
Remove the two phillips head screws that hold the valve in place. Pull the valve toward the front of the washer to remove it and compare it to the new valve.
To install the new valve, reverse all steps insuring tight water hose clamp and electrical connection. Install hot water hose, plug it in and turn on water. Test run and check for leaks. Unplug it and reinstall top.

Disconnected power supply and water supply hoses. Laid machine on its back because this is a top load machine. Removed one bolt to take off stator then 6 bolts to remove rotor. Put it on side without taking off wire assembly. Snapped off rotor position sensor and installed new one. Put all back together and connected power supply and new stainless braided hoses. WORKS PERFECT. Thanks !

Not too bad, had a neighbor help with the project as washer/dryer were stacked. removed dryer from on top out of way. Drained washer, tilted on side to get access from down below. Second person help here. unscrewed drain pump from front, Used pliers to unclamp hoses, disconnect wires to motor (already pulled power from wall) pushed plastic clip holding in unit and pulled out. New unit was factory new, not a knockoff. We took extra time to clean out hoses, especially from the main washer unit, it was a simple unscrew clamp and pull hose down. We sprayed out gunk from hoses and parts going back in. Once new unit was ready, installed back and reconnected hose and power. The clamps were somewhat of a pain with the overall size and angles to get them seated and on correctly. Much easier to take off, but take the time to reinstall correctly. Don’t need water leaking. Motor much quieter now, wife is happy.

Wife called me and said the washing machine just flooded the Landry room. I looked at it and didn't see anything wrong. Took the top off and the back off and started looking for a leak, did not see anything. Took the front part of the washer apart thinking the drain hole was plugged up where the rubber boot is. It was ok after taking the big rubber boot off or whatever that is called i was not getting anywhere. I put it back together left the top and the back off. I turned the water on and started the washer on a quick cycle looking for a leak. I found the bellows at the inlet had a small leak fixed that and started the washer again. So what i found out was the clean out drain plug was not in tight letting water out as it was washing after i tightened it all was ok. So i did find a leak that was small that we never saw. The hardest part was putting that wire clamp on the rubber boot it took two people to do that.

Had a puddle on the floor under the washing machine. While I couldn't definitively confirm the source of the leak, I suspect it was the drain pump. As such, I replaced the drain pump and the drain hoses (one of those 'while you're in there' things). The toughest part of the whole job was moving the washer away from the wall. I was able to leave the water hoses connected and just unplugged the electrical cord. Watched the YouTube video regarding the replacement and it was exactly what I needed. Just take your time and make sure everything fits together without force. In addition to the pump and the hoses, I had some drum shocks that I had previously purchased, but never installed. Replaced them at the same time. Everything fit together as expected and the washer works great. No leaks and reduced vibration. Good for another 15 years - hopefully.

Disconnect elec., hot and cold water supply and drain hose. Lay washer on it's back. Removed nut from center housing. Removed screws from stater. Disconnected wires with flat screw driver at sensor and stater. Installes new sensor. Put everything back together. Washer works great. No LE code.

We followed the installation video step by step that was found on another website.

I removed the Wire and spring from the tub seal and then removed the seal on the side of the washer that contains the Door switch. I removed the two screws that held the door switch in place while holding the switch with my other hand. Once the screws where out I pulled the switch assembly out thru the gap and removed the wires from old assembly. I then plugged the wires into the new assembly aligned the holes up and put the screws back in the new door switch assembly. I then put the door seal and tub seal holder back on. This took about 15 minutes. I do recomend that you unplug the washer before starting this process.

bought a position sensor
top load machine when i tipped the machine over i found
the nut and washer on the floor .replaced the sensor and nut
took about half an hour

Follow the LG washer video.

Totally dis-assembled this washer to check the bearings and drum plus fix the pump problem. We wash dog blankets occasionally and found the little drain hose from the front door gasket was clogged with hair. It makes a 90 degree turn and it gets caught there. THAT fixed the smell issue. As far as the pump replacement goes its quite easy. Videos online are your friend.