Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The door catch on your dryer is an important part as it keeps your dryer door closed, in order to ensure no air or clothes can escape. This part works by holding the door strike, which allows the door...
$50.91
In Stock
Order within the next 4 hrs and your part ships today!
This kit contains two coils, one is a two-wire secondary coil and the other is a three-wire booster coil. Both coils in the ignition coil kit should be used together in the clothes dryer. Some of the ...
$23.95
In Stock
Order within the next 4 hrs and your part ships today!
The door strike is attached to the door of your dryer and holds the door closed. If your dryer door is not closing, this might be due to the door strike needing to be replaced. This is a simple repair...
$28.95
In Stock
Order within the next 4 hrs and your part ships today!
This part could be found underneath a fridge, dryer, or freezer. The original foot may be cracked, broken, or perhaps missing altogether. If you notice the appliance is uneven to the floor or wobbling...
$32.95
In Stock
Order within the next 4 hrs and your part ships today!
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$21.95
In Stock
Order within the next 4 hrs and your part ships today!
This part senses the flame for heat allowing the gas valve to open. The most common issue that might arise that would indicate the flame sensor needs to be replaced is your dryer is not giving off eno...
$38.95
In Stock
Order within the next 4 hrs and your part ships today!
This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating. This part is located in the blower housing.
$54.40
In Stock
Order within the next 4 hrs and your part ships today!
This dryer belt is one of the most important parts in a dryer and is what allows the dryer drum to spin/rotate. If the dryer belt is damaged or broken, the drum will not spin or will have difficulty i...
75% OFF
$13.49
$53.71
In Stock
Order within the next 4 hrs and your part ships today!
This is a gasket, but you may also know it as a door seal, for your dryer. This part prevents heat loss during a drying cycle by keeping the area around the door sealed. This gasket is all black, and ...
$64.30
In Stock
Order within the next 4 hrs and your part ships today!
Ask our experts a question about this model and we'll get back to you as soon as possible!
7 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jeanne
February 7, 2020
How does the lamp assembly snap out to replace it
For model number 41791122310
Hi Jeanne. There is a release tab on the top you have to depress to remove. Thank you for your question and good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Ralph
February 25, 2020
The dryer heats up and turns round just fine but its making a ruff rumbling sound kinda loud. Ive cleaned out lint trap and back of dryer where much was accumulated but rumbling sound continues.
For model number 41791122310
Hello Ralph, thank you for your question. It sounds like it may be an issue with the blower and blower housing. We would recommend checking the housing for a loose blower wheel or cracked plastic. If that area is fine, the rollers, and idler pulley should be checked. I hope this helps.
The dryer does not turn off when the clothes are dry.
For model number 41791122310
Hello Patrick, thank you for contacting us. We would recommend checking the following parts to fix your issue: Door Switch, part number PS2330880, High Limit Thermostat, part number PS2367796, and Thermal Fuse, part number PS7783961. If you need help placing an order for it, please feel free to give us a call. We look forward to hearing from you!
Hi Joe, thank you for reaching out. Your dryer is 7.0 cubic feet. Its height is 36", width is 27", and depth is 30.3". Glad to be of help!
Was this helpful?
Thank you for voting!
Steve
April 19, 2024
Dryer runs for a bit but then stops and all three of the drying, cool down, and wrinkle guard lights flash quickly and continuously in unison.
For model number 41791122310
Hello Steve, thank you for reaching out. Based on the description that you have provided, we would recommend checking the thermistor, part number PS1149368, to fix the issue. It controls the temperature of the inside of the dryer drum and prevents the dryer from overheating. Glad to be of help!
The top of the dryer was easily removed by prying the front up with a screwdriver then tipping it back and off of the mounting brackets. Then the front of the dryer was removed by unscrewing a single screw on each side that held the front to the side panels then pulling the front away from the dryer. Once the front was off, the coils we
... Read morere easily accessible on the bottom left side. A metal bracket held the coils on and was somewhat tough to get the two screws removed on it as they were stuck, but once they were removed the coils easily came out and I was able to replace them in minutes. The whole job took 15-20 minutes and I now have a dryer that heats through the entire drying cycle.
1. Pry Dryer top up and off the clips. (Front of Dryer) 2. Remove 2 phillips screws on the inside of front panel. 3. Lift front panel up and set off to the side 4. Removed 2 phillips screws with short handled phillips driver that hold the gas valve coil bracket in place. 5. Unplugged and removed both coils, install
... Read moreed new coils and bracket. Re installed front panel, screws and top.
