58715383100B Kenmore Dishwasher - Instructions

For some strange reason my new dishwasher was installed without a door gasket, which caused a very small water leak. The gasket I purchased was installed in less than 5 minutes and corrected the problem immediately - a very easy task and I am no handyman!

First I removed two screws that held the door panel on. Then I pulled out the old gasket, inserted the new one, replaced the door and screws and it was done! We tested the dishwasher and no more leaks!

If you are getting intermittent leaks especially when you put a pot lid up front, it’s probably just the door gasket. And this was the easiest project I’ve tackled as a homeowner since buying the place 20 years ago. I read the other stories and I think the suggestion I choose to follow is not the best thing to do. So, read passed where I cut the gasket. I used needle nose pliers to grab the bottom edge of the old gasket which then pulled out by hand with almost no effort. I used the old gasket to measure the new gasket as recommended in one of the other stories, and cut it. DON"T DO THIS. The gasket is very soft foam rubber. As you push it in (I just used my fingers), it will get longer as you push it in. I put it in the first time (took about a minute if that long) and even though I cut it to the same length as the old one, it was too long. Obviously I figured I did something wrong. So, I took it out and measured it again. Nope, same-same. So, I put in a second time, careful not to stretch it, and this time it was now too short. So, I recommend that you just establish the bottom edge 90 degree angle seat and try not to stretch it as you work your way around the seam. It should fit just find, maybe with a little adjustment back or forth, but without cutting it at all. By the way, the half inch I cut off at the recommendation of one of the other reviews did not ruin it. It works just fine. So you can cut it if you want I suppose. But that half inch I cut off was what I was short when I was carful not to stretch it.

removed the screws holding the door together, then removed the screws holding the dispenser to the interior door. replaced the wires and put the door back together

Although the part I ordered was not an exact match, it was a Frigidaire piece and fit onto the spray arm assembley the same way. And if I do say so, it actually seems to clean the dishes better! All I did was clip the new one into place.

i just took off the old and poped on the new, it was way to easy! no tools required!

First I removed the two screws that hold the dishwasher in place, I pulled out the dishwasher and on the bottom right located the leak. The two brass nuts that hold the heating element in place. The wires had been rusted to the element so I cut the wires (and later spliced them back together) and unscrewed the brass nuts. I ordered the part after finding them very easily on partselect.com and 2 days later screwed them back on to the dishwasher. Spliced the wires back together and put the dishwasher back in place.

Easy Fix.

Turned power off , shut the water off to washer , unhook water line , unhook drain line from sink drain , unplugged electric chord from the wall . Open the door look where the door latches you'll see two metal strap' s that are screwed under the counter . Take the screws out . Take the bottom basket out .Take the spray bar off . There's two clips on the bar just push them out lift bar up .There in the middle of the washer you'll see filter screen. There's a small handle looking thing do not know what they call it .lol Twist one way or the other to take it off . Once you have that out of the way take the three screws out mine were hecksscrews .Pull the cover off remove the ball . Take a rag and take the excise water out in the bottom . Pull the washer completely out from under the counter . Lay it on the back side on the floor . You'll see the pump it has U shape metal holding it with two screws . Take the to screws out remove the U shape metal bracket . Unplug wire going to motor squeeze the clip and pull . Twist motor back and fourth and pull slightly till it comes out . Put new O rings on new motor and lubricate O rings and slide motor back in . Reverse the process . Take pictures if you need to as your taking things off if your afraid you won't remember.

It only took about 20 minutes to replace. Thanks for the video.

Removed 6 torx headed screw (loosens the internal control panel) and 2 philips headed screws(allows for front door panel removal). 2 torx screws had to be removed from existing latch along with 2 plugs loosened, be aware of how the plugs were connected to the latch. Do the reverse; attach plugs to new latch and reattach latch with the 2 torx headed screws. The 6 torx screws reattach the control panel and the 2 philips screws reattach the front door panel (be sure the front door panel is properly aligned prior to installation of the philips screws).

Disconnected power, water, and drain tube from dishwasher. Pulled dishwasher out and laid it on right side. It was not necessary to remove the pump motor. When disconnecting the water line, it is better to remove 3/8 line from the appliance adapter rather that the appliance adapter from the dishwasher as the nylon connection tends to strip.

Replace the latch. Got to cut off old latch, trim wires, install latch, and put on the dishwasher door cover back on with screws

My husband and dad actually did the repair, but my husband not being a handy guy said it was, 'so easy, anyone could do it!' He was very nervous about taking on the project, the longest part was testing to make sure it worked(running a cycle).
The simply pulled out the dishwasher, after disconnecting all electrical power, drained the rest of the water that we couldn't see from above, following the video given took out the old part without needing to take out the motor and were able to replace the drain pump, put everything back together besides sliding it into place in case it didn't work, in less than 15 minutes! When the short cycle finished and the water had drained they put it back into place and ran an energy saver cycle and it worked like a charm! Since then(2 weeks ago) we have now ran every function and have had no issues! Every time we open the dishwasher we comment on how much we missed having a dishwasher! Haha!

Most of the time is spent cleaning out under the sink, turning off water valves, disconnecting hoses and collecting water. One valve did leak when closed. Then pull out the dishwasher from under the counter, unplug and lay flat on floor.
Disconnect power from pump. Remove 2 screws and bracket that holds pump in place, gentle twist and pull out pump. Place tow gaskets around pump. Wet gaskets and gently push pump in place be sure to line it up so bracket goes back in place. Tighten screws, put hoses back in place, push dishwasher back, connect hoses, open valves, check for leaks then run the dishwasher and check operation of pump. I recommend viewing replacement on part select youtube video to determine if you can make the repair.

The Inlet valve was leaking. I removed the old valve in less than 30 min.Note: need bright flashlight! It could have been quicker but I had to lie on the floor and squeeze my big hands under the opening (kick panel). Once I got the two small bolts out, I was able to manipulate the valve out from under the dishwasher, then I carefully removed the two lines. I received the part in 5 days and installed it in 45 minutes. It could have been a faster installation, however I was not about to pull out the whole dishwasher. Again, I was able to manipulate the new valve back in & tighten then test everything.(note: need a bright flashlight to see underneath) I immediately ran a load of dishes and Presto! No leaks and runs like a Swiss watch!