59676064702 Kenmore Refrigerator - Instructions

I just removed the unit and replaced the mold/'heater with the new one and re-installed. It was very easy and didn't have to turn off the refer. or empty the frozen food.
However , there were not instruction that came with the mold/heater unit. I had no problem but other do-in-uselfers may need some basic instructons
Jim

This was a very easy repair. Of course start by unplugging the power cord. Take out the lower freezer drawer. Unplug the wiring harness from the ice maker at the rear of the freezer. Undo 3 screws with a 1/4" nut driver. The ice maker will come right out. You don't have to undo any water connections, the feed tube just slides into a guide in the ice maker. Once the ice maker is out, unplug the harness from the old one and snap it into the new one. Same with the cover. Reassemble in reserse order. Plug the power cord back in and wait a couple of hours for the familiar sounds of ice cubes falling into the tray.

Took under 5 minutes. Removed two screws and unplugged the wire bundle from refrigerator. Removed old unit. Put old wire bundle on new unit. Plugged wire bundle back into refrigerator and remounted the new ice maker. Could not have been easier. Watched the video first, it was very helpful.

Removed the old icemaker and installed the new one. The first one we ordered lasted about 4 weeks and pooped out. Parts Select was very nice and gracefully sent another in two days time. This one has been installed and is working fine...Hope it stays that way.

Thanks...Ron Norwood

, to remove the inlet tube holder/guide gadget thingee: (1) remove the three Phlipscrews from the motor end of the housing. (2) pull the housing straight off the end. (3) remove two Philips screws in deep holes that hold the ice tray onto the motor housing. (4) this frees the ice tray assembly, which you have to pull out, freeing the rotating blades, from which (5) you slide the sxle out of the middle of the inlet-tube thingee, so (6) you can then remove the inlet gadget from the ice tray.

You then reverse these instructions to reassemble with the correct inlet gadget. The tricky part is the front cover that hides the ice-tray from view. That cover has a couple of ears that have to fit into mating holes in the motor housing before you replace the two deep-hole Philips screws that hold the tighten the ice-tray assembly back onto the motor housing.

So it's too bad they don't see the ice-maker assembly with all the knock-outs inplace, so you can knock out the one you want. Other than that, it would have been no more trouble than other people have reported in working in the tight space inside the freezer compartment.

Replaced ice maker but now water valve wont work

Replaced ice ice maker using
All of the instructions on the website.
Very easy. A couple of the screws I had
To feel for because I couldn't gety big head
In the freezer far enough to see them.
Very simple and only took about 15 minutes.

installed replacement ice maker kit. 1st removed power. next loosened 2 upper phillips screws. then removed lower phillips screw and lifted and removed old ice maker. released wiring connector and pulled entire unit out of freezer. then i reversed the procedure to install the old unit. check youtube for instructional videos.

Unplugged the power, removed old icemaker by removing 3 screws and unplugging a small wire harness

Then i moved the wire harness off the old one to the new one, moved the end cover over to new one and plugged the harness back in and screwed it back in and turned it on

ALL FIXED!

Remove light lens by pushing straight back (needs some oomph, but not too much). Remove control housing by prying spring clips in back of housing with thin screwdriver or knife. Remove old control board by releasing plastic clips on both sections and removing 2 wiring plugs. Be careful snapping new control board in ; the alignment of the 4 switches and the 2 readouts is critical - easy to hang up a switch. Snap the control housing back into place, making sure that it is all the way in. Position the light lens so that it is lined up and about 1/2" back and then slide it forward (toward you) into place. The instruction sheet calls the refrigerator section the "fresh food" section. There are 2 light switches, one for each door. Both have to held down to get light to go out and enter programming mode. Easiest to close the right door, then push left door switch and quickly push the freezer DOWN button 3 times. Follow the instructions to set the program on the display and then push AND HOLD the freezer DOWN button until the display starts flashing. Release the freezer DOWN button, close the doors, open the doors to check. Display will indicate two 4s. (that was what mine indicated). Done.

The part just snapped in. super easy.

As per instructions. Removed parts from old ice maker, and installed them on new one, Then installed it in the freezer. Works good.

Remove 1 screw under ice maker. Gently pull downwards to unhook ice maker. Disconnected 4 pin wire connector. Remove and set aside the cover and wire loop you will need on new ice maker. Reverse the steps to install new maker. Once new ice maker is installed you will have to wait 2-4 hours for ice. There is a thermostat that will need to reach 10 degrees F to operate.

Instead of the ice maker unclipping from the wall after one 1/4" screw being removed from the bracket, I had to remove three of the 4 Phillips head screws from the ice bucket slider below the ice maker and swivel it down to allow the ice maker bracket to clear. The two 1/4" screws holding the ice maker to the wall at the top had to be removed and then the ice maker could be pulled away from the freezer wall. The rest of the instructions went according to the video and went well.

Unplugged fridge
Pulled light cover off
Used screwdrivers to press in on tabs holding control board cover.
Unplug wiring harnesses.
Snapped board in two.
Install in cover
Reattach wires
Done