66513939K010 Kenmore Dishwasher - Instructions

I took the top dishwasher rack off, then took off the old clip I had taped on. I hadn’t watched the video so I put the new one on by looking at the other side rail and inserted the new part matching the other rail, clicked the new clip on and I was done. it was quite easy for an eighty-one year old woman!! It did take me awhile to figure it out.

Watched a video and read through written directions.
Did not need to pull out the dishwasher from the cabinet.

First remove the front kick panel by removing 2 philips screws. Turn off the water supply, and then disconnect the supply line if not of the flexible kind. Mine was copper. Remove 2 screws holding dishwasher to counter top and pull machine out. Open door and attach replacement link by hooking the plastic end to the hinge hook on the door side and then place the string portion round the plastic pulleys and then attach the other end of the link to the end of the spring attached to the rear of the machine along the bottom side. Push dishwasher back into position, reattach supply line and re-install both screws attaching the machine to the counter top. Turn on the water supply and check for leaks. Place the kick plate into postion and secure using the 2 philips screws that were removed.

My wife hired a local repairman when the right side spring cable broke (I was out of town). He took two hours to fix it (and two appointments). The door would then pop open when running. He came back and replaced the latch. Problems persisted. I then ordered new hinges and replaced both in half hour or so. Would recommend doing all of these repairs yourself. None of these repairs are that hard and definitely not worth paying hundreds to do it. Trickiest part is pulling the dishwasher out from the counter without impacting the electrical or water connections. Disconnecting the power is important on all repairs. When you take the screws out of the door to get to the hinges, make sure you have a helper just to hold the door up while removing the last few screws. The left side hinge was really bent (when the right side spring cable broke) - caused the door to be out of square and thus would not effectively close. This was obvious after a 5 minute search on this this and other repair sites. Process that I used: 1. remove screws from both sides holding dishwasher into counter (may have screws into countertop as well). 2. turn off power, 3. pull out dishwasher far enough to see hinges and springs (careful of connections), 4. remove front door screws, 5. take off front panel, 6. remove spring cables (pull cable taut and remove "hook" from hinge)., 7. unscrew two screws holding hinge to door, 8. bend metal fingers around hinge pin to be able to remove hinge., 9. attach hinge in opposite path. 10. repeat on other side (if necessary), 11. reconnect things in opposite order...test door prior to reattaching door panel. Make sure you level the unit with the adjustable feet. Make sure screws in sides of cabinet aren't too tight as it can take the unit out of square pretty easily...

I looked at the position of the remaining Tine Pivot, since there are four on this dishwasher upper rack, and positioned the replacement pivot and pressed it into place. It was a snap (excuse the pun!). NOTE: My dishwasher's Model Number was not in the list provided herein. I had to search a couple of models to find the Upper Rack that looked like ours and to find the Tine Pivot replacement part that looked like ours.That process took longer than the "repair".

1) Pull out dishwasher from under counter. 2) Disconnect spring located at the bottom on each side of dishwasher. 3) Using socket remove pulley wheels from each side at bottom. 4) Install new pulleys on each side. 5) Wind pulley cord around both wheels and attach to one end of the spring on each side. 6) Using pliers extend other spring end to lower frame of dishwasher on each side. 7) Open and close dishwasher door to test. 8) Replacement complete

Followed the repair video supplied by the site

Attached new link, then stretched the spring with pliers and routed link over the pulley. Replaced both links.

Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.

It was very easy.

Very easy. I removed the two screws on the base plate, then the two screws that attach the washer to the cabinet, and pulled the washer out of its slot. I installed the broken side and closely checked the other side and felt it didn't need repairing. I put it back together and the door works very well.

Thanks,
Ted K.

Originally I ordered the rack stop clips but realized I needed the whole upper rack repair kit. It entailed pulling off parts and popping new parts on. Very easy and simple.

went to utube

My Husband did it

Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!