66515722990 Kenmore Dishwasher - Instructions

Removed the old mount from the upper rack. Removed the broken stem from the old mount that was attached to the arm. Attached the new mount to the spray arm. Attached the mount and arm to the rack.

Had to be careful positioning the spring without breaking the hinge pin. Requires a certain amount of patience.

I simply had to hook up the power cord to the dishwasher so i could plug it into the outlet rather than direct wire the appliance. Everything went very smoothly. Everything needed for installation other than tools was provided. Easy to follow instructions if you know a little about electrical wiring.

but the pin in and add the pin though the 2 tabs close door on it open it up move the springs backwards to the door

Removed 2 screws that held the old mount and washer arm in place, new mount was very easy to install, it snapped in, only one screw needed, remounted the washer arm and the job was done. I was really impressed with the ease of ordering and how quick it got here (3 days), also the scematics you have online are very helpful. I printed them out since I don't have the owners manual any longer, they're very helpful in matching up and ordering the right part which saves a lot of time, also I like the way you can just search by model number and appliance name to find the right parts, makes the entire process really easy. I know I will continue to shop here when the need arises. It really cuts down on expensive repair costs.

removed two hose clamps and old hose. slid new hose on existing fittings on dishwasher drain and disposal and tightened hose clamps. Turned it on for test run.

I unscrewed the wash arm tube from the agitator, and then unhooked the plastice holders that held the arm tube, pulling those parts out of the dishwasher. I took the new (one piece!) wash arm tube in hand and then realized that I would have to cut the plastic holder in half because there was no way to get the new (1 piece) arm tube through the plastic holder. I cut the plastic holder in half, fit it around the arm tube, and super glued the holder back together, allowing it to dry for several hours just to be safe. After that, I simply screwed the entire thing back on, and we were good to go. It could not have been easier, except for the unexpectedness of have to cut the plastic holder. Saved us probably at least $100 worth of service call and parts.

Install too less that a minute. Fit perfectly.

remove star screws holding inside door panel. remove plastic cover that protects latch assembly. hook one end of spring on stationary pin on inside of slider bar. Hook other end of spring on pin on slider bar. replace cover and door panel.

Actually I ordered the drain and wash impeller kit because it was listed as the #1 cause of failure to drain. I then hired a plumber to install it. He did so and that didn't solve the problem. So I was about to buy a new dishwasher. I then noticed that the second most frequent cause was a problem with the "dishwasher drain check valve." I watched the "partselect" video on how to change that. I didn't have a new one but I thought I would take out the part and see what I could learn. As it turned out it was blocked by a little piece of what appeared to be a walnut chip. I cleaned it out reinstalled the drain check valve and the problem was solved.

Put in both a new element and thermostat. Did not fix problem. Using an ohm meter I did not measure any voltage to the thermostat. Suspect it’s a problem in the control unit, and decided to replace dishwasher.

Replaced door gasget took 5 minutes tops. Ran cycle and still had leak. Called local repair person. After thoroughly checking out the dishwasher and running soapless cycle determined problem to be soap build up over time. He ran a commercial cleaner through a complete pots and pan cycle. No more suds and no more leak repair complete. Did not actually need door gagset but it was super easy to change and delivery service was great.

Installed pump kit. Was surprised the kit seemed different( some parts changed or deleted. Instructed to discard old parts and follow with new configuration. Reassembled and tried t fin it works fine now. Thank you so much

I watched the video link sent in an email and followed exactly what they did in the video. I removed the star head screws holding the door liner in place. Then removed the protective cover on the inside. I disengaged the component holding the latch in place. I replace the component that holds the latch in place and then snapped the new latch in place. I turned the dishwasher dial until the prongs were fully retracted. I replace the protective cover and then put the door cover back in place. I initially only placed the left bottom star head screw until I was sure that the latch was going to release. I tested that it was working properly by slowly turning the dial on the dishwasher control. Once I knew it was working I replaced the rest of the screws.

removed old check valve from bottom of dishwasher and replaced with new one. I used channel locks to do this, disconnect hoses and screw out check valve, and put back in opposite order, make sure the dishwasher is empty of water or have a plastic bowl or such to catch water. Take off two front covers on bottom of dishwasher to access check valve ,white with hose attached.