66515782300 Kenmore Dishwasher - Instructions

Installed the new upper spray arm mount. First I installed it backwards which made the blades not turn freely (rub against top rack basket). Turned it around and was good to go. I found it helpful to remove the top basket in order to do this. Note that this clip is gray while your dishwasher tines are white. This does not cause any harm.

unscrewed sprayarm, removed bearing and seal, used PartSelect pic and description schematic to identify part numbers then placed order. Parts arrived in two or three days.

I first removed the old part. when i removed the old part i could not get the conector piece off when i when to get a new one they told me i should replace the copper tubing with the more flexable tubing because the copper tubing can kink up and possibly break from the kinking. so i screwed the inlet valve on i put teflon tape on the all the threads of the conector piece screwed it into the new inlet valve with and adjustable wrench then i conected the new tubing, and tightend it down with the wrench i slowly turned the water back on to cheak for leaks. When i saw there were no leaks i turned the water on the rest of the way pushed the dishwasher back in and screwed it into place an i was done.

Looked at other side of top rack which still had the stop. Just had to orient the direction of the stop and push it firmly onto the rack arm. Took a couple tries, but it went in and locked. Works perfectly. Inexpensive and easy fix to to very annoying problem.

Pulled off the old valve using a crescent wrench and screw driver. The replacement part was a 100% exact match. Slapped on the new valve and that baby was water tight. $50 on a new valve is a lot better than $500 for a new washer.

Partselect.com was so easy to use and find the right part. Way more helpful than whirlpool's site, but that's not surprising seeing as they have an "authorized repair technician" page.

Thanks Partselect.com!

actually my wife did the repair. she unsrewed the water sprayer and removed it, then unscrewd the star key screws and then replaced the seal. she put everything back the way it was and it is now ready to use and we no longer have the problem.
just a suggestion...if you take some baking soda and some vinager you can clean the drain out. just simply poor in the soda and then the vinager.and it will fiz cleaning your drain.

first I removed lower basket. then removed lower sprayer attached to pump housing by unscrewing the cap by hand. the I removed the pump cover . there were six alan screw two of them were missing causing the failure of the seal spraying solution at the door. replaced the pumpseal working backwards until everthing was replaced.

Eay repair. Replacement tube was one piece and only required removing one phillip's head screw to replace

I followed the video available on partselect.com and was easily able to follow step by step the process of removing and reinstalling a new Drain and Wash Impeller and Check Ball.

Snapped the new stops on. It took about 2 minutes.

All I had to do is lay the shield over the top and sides and used a couple of clips to hold in place as it was slid under the counter top. It couldn’t have been easier.We had searched everywhere for this replacement shield and parts select was the the only ones that had it. Very good service and fast delivery,

Turned off electricity. Removed the interior door cover. Removed door switch. Replaced switches & reversed process. By the way - I am a woman & diagnosised, ordered part & fixed it myself - I have no experience in this field. THANKS for all your information on your site.

Removed the old mount from the upper rack. Removed the broken stem from the old mount that was attached to the arm. Attached the new mount to the spray arm. Attached the mount and arm to the rack.

Had to be careful positioning the spring without breaking the hinge pin. Requires a certain amount of patience.

I had a broken spray arm on the dishwasher and though i would have to spend $450-$500 on a new dish washer, i ordered parts from part select(even though i was not 100% sure if it will work), the parts were shipped super fast and arrived in 2 days, i was able to replace the broken part and fix the lower spray arm. Part select saved me a lot of money.