66575776890 Kenmore Range - Instructions

Put the bottom of the glass in first then put the top half into the brackets in the door handle. Holding it in place with your extra set of hands tighten it down with the two screws from inside the oven door into the back of the handle. The door will be open a lot so be extra careful not to let the door close onto your hands or fingers. Also remember patience is a virtue.

I use the table knife to slide the side of the stove to open the top. then I traced one of the wire to where it was hooked up and remove it and replaced it. I did them one by one.

The brief comments on how to with the order was most helpful, no problems replacing frame. Quality is good I thought the price was very high for the parts, considering plastic and metal pieces, but then again compared to new stove reasonable. Remove pieces replace back in order removed.

We cheated; a local appliance repair company was called & the tech guy repaired it in 10 - 20 minutes. Couldn't be happier.

I still don't have it back together! The first time we ordered the part the gentleman sent me the trim for the left side which seemed to be fine but while replacing it the old part (right side) broke. Ok. so I called to order same part but for the right side. Well, the lady told me I could only order the oven door trim kit, which seems to be too large. I don't think she understood me. Why the 1st time ordering I could get the left side only now when ordering the right side she says we don't sell it that way. Very confused and still can't use my oven since Dec,19th!!

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

took out old oven bottom by removing 2 screws, placed the new oven bottom in place put the screws back in and was done.

Took off oven door removed all screws to get old hinges out. Replaced with new hinges and put the door back together.

I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy

DISCONNECTED POWER AND GAS TO THE RANGE. REMOVED 6 SCREWS FROM REAR OF THE RANGE. REMOVED THE 2 SCREWS HOLDING THE TEMPERATURE SENSOR IN PLACE. DISCONNECTED THE LEAD FOR THE SENSOR. INSTALLED NEW SENSOR IN REVERSE ORDER. OVEN WORKING PROPERLY NOW.

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

Took the back off the stove, removed 2 screws, unclipped the bad sensor, clipped the new one on, put the screws back in and the back of the stove back on and that was it - 10 minutes

Loosen 2 screws and put new part in and tighten 2 screws. After putting in new sensor stove gave me another code had new part in 5 min and part select would not take my part back.

Only one screwdriver needed for this simple repair. Unfortunately for me it did not repair my oven and a new code on the oven indicated a bigger problem with computer board.
Part Select was great to work with and accepted a return and promptly refunded me for the part.
Thank you!

Unplug the electrical cord. Remove all the grates and burner caps. Remove the two philips-head screws on each burner. Slide the plastic putty knife under the cooktop in the front to locate two clips. Push in to disengage clips and lift cooktop up in front. Disengage cooktop from the rear of the range. Remove the bad igniter from the burner head and replace with the new, Disconnect the wire from the spark module and install the new wire. Replace the cooktop by securing the rear first and then lowering into place until the clips engage. Replace the philips screws on the burners and the caps and grates. Plug the range back in and you are done.