66598002701 Kenmore Range - Instructions

Real easy, I removed the two screws holding the element in place, then pulled the element out a few inches to reveal the wire connectors. pulled the connectors from the old element and then replaced with the new one and screwed it back into place and presto! All done and cooking again. The replacement part came in 2 days fast and reliable. Thanks PartSelect.com

Turned OFF the circuit breaker. Unscrewed the old and screwed in the new. Very easy. There were helpful hints from other people on the web site, ie. turn off the circuit breaker first.

1st - UNPLUGGED appliance from electrical source!! then removed screws to open ceramic stove top, disconnected wires from dead element, plugged in wires to new element, closed stove top, turned on burner - it worked!!

only problem is that "hot burner indicator" does NOT stay lit after burner is turned off!

Put a new one in.

Easier than making a pie! Unscrewed 4 screws and detached the element from the back of the small upper oven. Connected the new element and put the 4 screws back in place. We saved $129 service fee by doing this ourselves not to mention the markup on parts. Shipping was very quick! While I hope to not have to do this again...I would do it again in a split second!

I took the back panel off, removed the old lens, installed the new lens. How easy to order from home, receive the part, do the repair and pay less than it costs to simply drive to the parts house. Cool....

swap a known good coil around and still did not work. then measured voltage across the switch terminals and found out one leg was opened. Ordered a new switch which looked alike. The new switch could handle more current than the old one. Turned out that all terminals of the new switch were same size while the old one had 1 smaller size. Used the dremer tool to file it to fit the wire terminal. Also the burner knob had different grove type . Just forced it in.

Removed old assembly, attached wires to new and inserted into space for same. Of course you must turn off the range circuit breaker. The part that took the most time was removing the old assembly. Once that was done, the rest took only a few minutes.

The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in place! Simple!

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.

Removed two retaining screws and pulled out coil. one terminal came off readily but one remained and was difficult to get off. Pulled range out from wall and removed cover plate and removed existing terminal connection. Pushed new coil into oven openings and screwed in. Slide terminals on in the rear of range and replaced cover plate. Took about 1/2 hour because I was nervous.

IMPORTANT NOTE: This element is shaped like a B. The straight line part of the B, which is closest to the back part of the oven, doesn't light up. At first I thought it was a defective part. My husband is the cook and I never realized this. This fact isn't indicated in the instruction booklet which came with the oven. My sister has the same oven and she didn't realize it doesn't light up either. I looked up installation instructions on You Tube and although I was very nervous, it was easy to install. It's a little awkward because the wires are in the back of the oven so have a flashlight handy.

Two Screws on the back. Pull out heating element and remove wires. Install new wires and replace screws. Done in 5 minutes

Husband took old one out and put new one in. Did not have to pull stove out. Be sure and disconnect the power at the electric box. Only 2 screws holding the element in. Easy fix, just wish they would last longer.