All Installation Instructions for LG Washer Dryer Combo 706574

Dryer quit spinning

One of the roller assembly froze up & had a flat spot on it. There for causing the drum not to rotate. Pulled it out replaced the roller & up & running.

Parts Used:

Roller Assembly (Pack of 4)

Peggy from San Bernardino, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Dryer door hinge broke.

Followed YouTube video repair process. The only problem is that the door hinge has plastic bushings attached. A couple broke and the parts listing does not show the bushings, nor does the hinge come with them. The door is a bit loose without them. Nonetheless, the repair did the job for now.

Parts Used:

Hinge

Raul from CYPRESS, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

igniter would not light

Initially replaced igniter. Didn't think it was bad though. Read other suggestions on another website. None were the correct diagnosis for my situation. And when I figured it out they did not offer correct part. The dryer thermistor temp sensor (probe sensor) is what I replaced. Found it on Parts Select. I did replace other parts also. But that's the one that ultimately was the issue.
Was not hard at all if one is even a little handy.

Parts Used:

Hi-Limit Thermostat And Thermistor Kit

Dave from SAINT JOHN, IN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Needed to replace dryer filter

Pull out the worn out dryer filter and replaced it with a new filter that I purchased through Partselect.com.
It fit perfectly.

Parts Used:

Dryer Lint Filter

Mike from LINO LAKES, MN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Dryer work but wouldn’t shut off when finished cycle, had to shutoff from breaker

With a thin flat screwdriver I was able to pry out the old door switch, I replaced it with the new door switch, pushed back in dryer and so far is working since I installed a month ago.

Parts Used:

Safety Switch Assembly

joaquin from MIAMI BEACH, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The old lint filter was worn out.

I took the old lint filter out and put it in the garbage. I the put the new lint filter in the dryer. Problem solved

Parts Used:

Dryer Lint Filter

Dennis from N SALT LAKE, UT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Dryer door latch broken

Part showed up in 2 days and repair took 2 min. Very easy. Thank you!!

Parts Used:

Dryer Locker Assembly

Paul from OVERLAND PARK, KS
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Added air diverter on exhaust hose and blew out heat limiter fuse.

Entered dryer from rear exhaust port. Removed 2 screws and 2 clip on wires. A little awkward of process but superior method over disassembly of drum and main parts.

Parts Used: