75559 - Instructions

Have had the Sears repairman come to the house to replace this part in 5 minutes for +$100.. twice. When my dad's stopped working, ordered the part and replaced it myself for the cost of the part and shipping.
Use a screw driver to pry the right side of the switch and pull out. Best to watch a youtube video first. Takes about 5 minutes.

Unplugged the refrigerator, Taped around the edges of switch as I had read to prevent possible scratches, used very thin flathead screwdriver to pry out old switch, unplugged old switch, plugged in new switch, put it back in opening, plugged fridge back in, and I had beautiful light! Hardest part was unplugging the refrigerator!

Unplugged the refrigerator. Used small flat head screw driver to push the front tab of the old switch in and pulled it out with pliers. Detached and reattached the wires to the switch. Reinserted back into hole. Plugged refrigerator back in to power. All good.

pried out old switch, disconnected wires ,placed wires on new switch

The old switch was a little hard to get out....took me a couple tries. I couldn’t move the frig out to unplug it, so just shut the power off in the kitchen. But, I was happy that’s what the problem was and so happy to have the light back on......it was probably three years it didn’t work!

Removed the large freezer drawer bin. Took out the 2 screws holding the door to the rail, pulled drawer off the rails and set it aside. Note: the drawer still has the non-sliding part of the rail assembly attached to it. Reached inside the freezer and pushed the tab holding each of the rails and slide out the old rails. Removed the bolts on the freezer door holding the remaining part of the rail assembly (The white part). Attached the complete rail assembly to each side of the freezer drawer. Inserted the drawer and newly attached rails into the slots holding the rail. Slid the drawer in which allowed the rails to slide over the holding tabs. Checked door for in / out sliding easy and inserted the large bin back into the unit. I had purchased the full L & R rail assembly.

Pulled fridge away from wall, unplug electrical connection, open fridge door, use knife to prize out door switch, pull off and replace switch from electrical wiring.

Replaced old hose and installed the new one. Was very simple with the instructions in your email..... step by step, could not of been any similar.... you guys rock

I took a very thin bladed screwdriver and took the old part out -carefully.
The new part fit in quite easily.

I had previously watched a YouTube video (do this first!!) on a similar Kenmore model so I knew what to look out for: (1) turned off power, (2) took thin putty knife to slip under outer lip of switch (most screwdrivers are too thick), (3) wiggled switch at front end to release the tab, (4) unplugged from the socket, (5) plugged in new switch, (6) popped new switch back into door, (7) turned on power. Voila !! Super easy. I couldn't believe it.

Removed old rails and tapped new rails in place. The big problem was finding how to fix the drawer. After searching many online websites, It was my good fortune to find Partselect and a one of their service representatives who
knew how to fix my drawer
and they had the part.

Food off top of shelf, drawers come out, glass tops come off, lift the whole unit up (can be a little heavy. Tilt sideways to angle past doors (remove door's lower bins as needed by removing food and lifting up). Turn upside down, remove 3 screws from metal rod and remove metal rod (may require prying out with screwdriver). Remove textured plastic top pieces from each side; some flexing is required to get one side up, then the other. Remove two hinged drawer covers by pinching in at their hinge points.

This is your last chance to clear all the walls, floor, and ledges at the bottom of your fridge. Just sayin'.

Put new shelf upside down on counter. Transfer metal rod to new shelf, screw it in. Transfer hinged drawer covers. Transfer textured plastic topic pieces, again putting one side (of each) in first and flexing unit a little to get other side in. Turn right side up and angle back into refrigerator.

Bring shelf flat and push to the back of the refrigerator until it is flush with the back. Lower whole unit until it rests on top of the side rails where drawers slide in. Left side has a tongue that will fit into a 2" or so notch near the front, right side will rest on top of a round bumper. Front coldness control should still operate smoothly. Put drawers in to make sure they glide and close smoothly. Put glass shelf on top and press down lightly to make sure lower shelf is stable and glass fits neatly into its plastic frame. Replace any door bins you removed.

Ta da!

Followed instructions online

I found a crack in the pex line from the valve up the back of the refrigerator to the water filter. I could not find the correct 5/16" size line locally to replace it. A guy in plumbing at Home Depot said he always repaired them by cutting out the crack and finding a piece of clear vinyl line that would fit tightly over the cracked pex to splice in a fix with hose clamps. I did that and it was a really bad idea. The line was obviously fatigued and failing because it just cracked further up and leaked again. I then looked up and ordered the correct line (actually both the supply and return since they were available). Installing the new lines was a breeze. The pex connectors are simple to disconnect and reconnect. Wish I had done that to start with. I looked for a youtube video for the proper replacement steps but all I found was a video of a guy who cut out a crack and stuck a pex connector in to replace the cracked section. By doing that he pulled slack from the valve end of the line which didn't exist and cracked the line again. I don't know why anyone would mess with patching one of these lines. The correct parts are available, cut to the right length, and removing and replacing them at the valve and the filter is dead simple.

Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.