79031049800 Kenmore Range - Instructions

removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,

Removed two screws that are attached to handle then removed four screws from bottom edge of oven door. I was then able to remove the outer door glass,this gave me access to the three inner glasses. After removing the retainer for the glass assembly,I was able to remove all three and replace the inner one.I reversed this proceedure to reassemble.

Disconnected power cord to range
Removed the cover over the flame guard
Removed the Flame guard
Pulled out broiler drawer
Unscrewed the cover and disconnected the white plastic connector to the ignitor wires
Un crewed the two small screws to the ignitor and removed the old ignitor
Cut the two wires from the old ignitor
Connected the new ignitor to the wires on the white connector
Installed the new ignitor
Reassembled parts dsassembled
Plugged in power cord

Works

Remove bottom plates and deflector from oven, remove old igniter. Remove bottom drawer and panel to expose wiring. Cut wires, used supplied wire nuts to splice. The time consuming part of this job was having to clean all the parts before reassembly, and having to extract screws that were rusted into place due to heat and spillage. One of the igniter screws was stripped, and was very difficult to remove. The first part in your "probably cause" list was the right one! Thanks for the good service, and a useful website!

Was easy...I pulled oven out from the wall so I could get to the back.i used a nut driver to remove small silver cover.matched up wires to the never module and re installed.pluged oven back in and burners lit perfectly

unscrew the sensor inside the oven; took off the back of range to access harness of sensor; the replacement part harness did not match up to the original, so we stripped the clip from the end of the part and also the end of the harness in should clip into. after joining the wires together with ceramic wire nuts we tested the oven to make sure all worked AND IT DID!

Remove oven racks and bottom oven panel cover.Removed old igniter.one screw was stripped so that slowed me down quite a bit! Used a small vise grip tool to remove screw! installed new ignighter,cut existing wires; spliced in new wires( be sure to unplug appliance) tested ok. Reassembled.

Oven would not light upon setting for oven heat-up. Igniter would glow, but no gas flow. Gas Valve safety not sensing enough current draw from igniter to open gas valve. Original igniter measured 175 Ohms on Volt-Ohmmeter. New Igniter measured 74 Ohms before installation and use. Installed and spliced into existing wires using good quality wire nuts and tucked wiring into wire areas ensuring it was away from burner flue. Oven lit on first start-up! Problem fixed! Easiest to get to by removing broiler drawer, pressing catch tangs in from outside rails using a small screwdriver. 1 screw of 2 on igniter mount was stripped and difficult to remove, but working with pliers and nut driver was able to remove it with some difficulty. New Igniter hangs fine with 1 screw. .

Having already removed the old igniter , replaced it with new.

Replaced the ingintion module, still did not work, replaced the burner complete with new ingiter , it now works but another one quit . the front right one has 5 ohms resistance ,replaced with new one with 0 ohms, the back left has 2 ohms resistance and now it does not work , will need to replace that burner allso. too bad you can't buy just the spark module for the burner.

first I removed oven draw for access, then removed the two screws with a nut driver, next removed the two wire nuts and the old element was free. Replaced new element in reverse steps of removing old and the new part ignited the stove within 30 seconds, but now I have no excuse for not fixing dinner!! Thanks for promt shipping, it arrived early than anticipated.

Really easy to do, did not have to bring stove out from the wall! Turn power off to the stove. Remove the lower drawer. Remove the oven rakes. With a slotted screwdriver remove two screws in back of bottom oven cover, use 1/4 inch socket to remove two screws in front. Remove bottom oven cover. You can then see the part to be removed which has two wires going into it, the unit looks identical to the new part which heats up and lights the gas grill for the oven. I cut the two wires from the old part, remember which is the upper and lower; remove two screws holding onto part. Wire new part remembering top and bottom. Push extra wire down into bottom drawer and then mount new part with two screws. Turn power back on and try oven. Lite right away for me so I knew I had replaced the bad part. Reassemble and Enjoy!!

1. Loosened 2 sensor mounting screws and removed them. 2. Tripped range circuit breaker to off. 3. Pulled out the range but left gas connected. 4. Loosened the 4 screws on RH side of the top back panel and carefully pried that side of the panel open. 5. Using fingers, threaded the sensor's wiring harness through insulation and into the oven. 6. Unplugged old probe. 7. plugged in new probe. 8. tugged wiring harness back through insulation behind the oven. 9. Using 2 screws removed in 1 above, mounted new sensor. 10. Repositioned top back panel and fastened it in place. 11. Shoved range back in. 12. Tripped range circuit breaker to on. 13. Reset clock. 14. Set oven to 450 for test tun. 15.

1- put in new thermostat 2- put in new gas valve 3- put in oven igniter ....3rd time a charm. Now I have all new oven parts! My husband installed and said it was pretty easy, have to take the oven door off and inside bottom out.

Removed oven door, removed oven floor. Unscrewed skirt with attached igniter and gas tube. Two nut screws hold igniter to burner. Remove old igniter and replace with new, reattach two wires with supplied wire nuts. Replace oven floor and door. Oven lit right up, pizza anyone?