79045594900 Kenmore Wall Oven - Instructions

Wife was cooking our thanks giving turkey, when an oder of burning was noticed. I walked over to the oven and smelled the area of oven light, it was bad. I turned off and unpluged oven. Got a screw driver, unscrewed 4 screws then noticed the burned switch from under the oven top. removed 3 wires, covered w/ elec. tape, and pulled oven light switch out front. looked at part number and ordered online. We were able to cook our turkey and enjoyed our meal.

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

Simply took oven out of wall, removed back plate, unplugged old sensor, went in the front and unscrewed old sensor, put in new sensor, went in back and plugged in new sensor, put on back plate, push oven in wall. Turn on power

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Remove 4 knobs from front of stove.

Remove plastic nuts that are directly underneath oven knobs. Loosen with plyers and unscrew.

Remove front cover.

Remove 8 screws holding down electrical panel. Remove panel. Remove 2 screws holding switch into place. Transfers wires from old switch to new switch so you hook them up correctly. Then reinstall in reverse order. Job complete in 15 minutes.

1 Turned off the oven breaker.

2. Removed the oven racks.

3. With a Phillips screwdriver, removed the mounting screws holding the temperature sensor and unplugged it.

4. New sensor plug did not match 20 year old connector. Had to cut and solder splice the connectors.

5. Installed the new sensor and now oven holds temperature steady.

Easy order, quick delivery and easy installation, happy wife.

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

Watched the repair video on your web site. Used the video as a step by step guide in the actual repair.

Pulled range out from cabinet, removed back plate, two screws inside oven attaching the temp sensor. Then pulled the sensor and wire through from back. Reverse to replace about Ten minutes
OEM parts plug in same, works great

Phillips screwdriver used to remove 2 screws at top left in oven. Pulled thermostat out until I could get to the connector. Used pliers to hold wire, reconnected new plug , threaded it back into back of oven and reattached the two screws.
Saved $150 on a service repair call.

2 screws disconnected old one and pulled out the new one in put in opposite way. The representative was so helpful, part came fast. thank you

Googled the problem and found Oven Temperature Sensor and Main Terminal Block to be the most likely problems. Turned out to be neither. No parts were needed. Oven has a thermal overload switch on the rear upper left. Thermal overload needed re-set. To do so you have to remove the oven, remove the back and press the red button on thermal overload. Biggest challenge was figuring out how to remove the oven. Even with the installation manual it was not easy to fgure out. The instructions are misleading. You need a special tool. I used two hacksaw blades as a substitute, and slid them in to release the clips. Once you figure out how to get the oven out the rest is simple.

Removed two screws that are attached to handle then removed four screws from bottom edge of oven door. I was then able to remove the outer door glass,this gave me access to the three inner glasses. After removing the retainer for the glass assembly,I was able to remove all three and replace the inner one.I reversed this proceedure to reassemble.

removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,