79045799100 Kenmore Wall Oven - Instructions

my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.

Bottom oven quit heating about 6 mos. ago and now top oven quit. Broiler worked fine on both. Bought 1 replacement element to try. Did not work on either oven. Found online where someone had found a bad solder joint on a relay board so I pulled the oven and removed the covers. (WITH POWER OFF. I made a diagram of the wire connections to the board and removed it. I FOUND a cold solder joint on the L2 connection of the top oven board. I found the exact same cold solder joint on the bottom oven board also. After resoldering the connections and touching up any suspect joints I replaced the boards. They BOTH WORKED fine!
Anyone that can't solder can take the boards to a local radio/TV repair shop and probably get the techincian to resolder it for a minimum fee. It is certainly worth the attempt.

We pulled the stove out from its slot in our island. We unplugged it and unhooked the gas line so we could get behind it easily. We then took off the back (using screwdriver) to get to the connectors for the element. We unhooked the connectors from the old element. Then we took off the plate inside the back of the oven (using screwdriver)and gently pulled the old element out. We seated the new element in the oven and then hooked it up in the back and put it all back together again. It worked perfectly! The hardest part was cleaning the dirty floor under where the oven had been for 7 years!

It's kind of embarrassing!
As the breaker was being thrown to turn the current off, I discovered that the breaker box was burn up at the breakers.
Short story but I got'er done! The problem now is there is something still wrong with teh oven!
I think I see a new one in the future!
Thank you very much for the very prompt delivery.
My purchase has been without a flaw.
I have already sent the part back for a refund.
It cost me something like $13 for this experience for freight.
I will remember you with my next need.

Just "locked" the hinges, pulled the door off. Removed the broken glass for the door. Switched the handle from the old door to the new one. thPut it back on e hinges.....viola!! new oven door glass!

I had to replace the clock /power panel on the stove. It did not come with a face oover. Both installations were fairly east once the problem was diagnosed. The control part did not show a face plate not included, or needed. I had to reorder the overlay . The job came out perfect and my stove looks like new again.

replaced it

Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.

After trying to unscrew a plate on the side, I found that would NOT work at all, the side panel of the stove was behind it. I found a tab that cut-out on 3 sides just above the location of the recepticle, and simply bent that tab out, pulled out the old recepticle, slid in the new recipticle, and put in the screws and then bent back the tab. It was sooo easy once I found that. I repeated in on the other side.

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Easy as 1-2-3

watched a U-Tube video on this subject.....worked like aa charm!!

Square drive screws used throughout the oven since its manufactured in Canada. Shut power down to the range. Element fastener plate removed and 2 electrical terminals loosened. Used a pair of hemostats to hold on to the wires so as not to lose them to the interior back of the oven which was loaded with insulation. Connected the 2 wires to the new element, screwed the element fastening plate with element back to the back of the oven wall. Turned power back on and voila, I was back in business.

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.