All Installation Instructions for Kenmore Freezer 79575196400

Crack In Old Tank Assembly

Removed the old, replaced with new. . . That easy.

Parts Used:

Water Tube

Mark from Port Angeles, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

broken part

replace piece

Parts Used:

Tray Cover

Lisa from Santa Fe, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

interior lights stay on

Changed door switch. Repair worked for a few days but re-occured. Possibly the other switch is bad .

Parts Used:

Refrigerator Push Button Switch

Rich from Pequannock, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Plastic pin broke

Real Easy

Parts Used:

Button,Lever

Donald E. from Roseburg, OR
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

door mounted cold water tank was leaking at seam of polyethylene tank.

The part labeled as water tank was not pictured on web site, and when it arrived it was a large coil of plastic tubing wire-tied in an oval shape,not a blown p/e tank as original.The oval of tubing would not fit into the door compartment, because of the bulk of the actuating solenoid. No instructions were included. It was necessary to hacksaw the steel solenoid mounting bracket off the solenoid, then contort the solenoid into the compartment to get all parts inside the cover. new connectors had to be purchased, because the the tank/tubing coil was 1/4" od, while the original tank had 5/16"od connections.

Parts Used:

Water Tube

RONALD from LAKE WALES, FL
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

The gasket on our bottom drawer freezer was torn

Simply used a flat head screwdriver to get the first few inches of the gasket out of its track and after that just pulled it by hand. New gasket slipped over the door, lined up the corner and pressed into in the track. Checked to see that it was snug all over and we were done. 5 minutes at the very most. Never would have noticed this. Took all the bins out of the freezer to give it a good cleaning and noticed the torn piece hanging. Our refrigerator runs much less often. Expect to see a difference in our electric bill!

Parts Used:

Refrigerator Freezer Door Gasket - Black

Pat from West Bend, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

vegetable tray assembly fine.

I need the slide rails right and left for the center of the trays.

Parts Used:

TRAY ASSEMBLY,VEGETABLE

Walter K from Newport Richie, FL
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Interior Light Would Not Turn Off

Tape off the light button so door alarm does not go off. Take off the clear light shield and remove the light bulbs. Be careful, bulbs may still be HOT!! With Phillips head screw driver unscrew the light plate assy. Drop it down in a comfortable position. Disconnect the connector, unscrew the thermal sensor and remove light assy. Install new light assy into light plate assy. There is no thermal senor in the new assy. Snap light plate assy back into place and install the two screws previously taken out. Install bulbs and clear cover. Remove tape from light door switches and you are done. Lights should go on and off when door buttons are pushed in and out.

Parts Used: