79680318900 Kenmore Dryer - Instructions

I did as I was told (by my wife). Bought the machine from Home Depot - no side vent kit - had them complete the installation today when the kit came.

My cleaning lady brought her handy husband over Saturday to help me. The only tool we used was a Phillips-head screwdriver. I went online earlier in the week and found a good video put out by Repair Clinic and another one I found on You-tube on how to disassemble the dryer. After watching several times, I knew I could do it. We worked together, I cut my hand on the inside edge of the control panel, but, when I hit a snag, we watched that part of the video again and worked right through. Replaced the Thermistor, NTC first, not a problem. Then the Heater Assembly, not too difficult. I couldn't find where one of the remaining parts went, so, we reassembled the dryer and gave it a try. Worked like a charm. We did remove a lot of lint from inside the cabinet and around the felt liner on either end of the drum. It works like it did when it was brand new. Highly recommend to work with someone, so, you don't get frustrated. I am 65 years old and this was a no brainer for me, although I am somewhat mechanically inclined. Very empowering to accomplish this repair. Just follow the video.

I took the top off, I disattached the front and took the front top of dryer off, taking the front of dryer off, detached the belt and took the drum out, found the wheels took the plastic triangle off and took the wheels off and replaced wheels, then did everything in reverse and no more thumping. just remember to unplug unit before working on it. And also Part Select is a very good site and place to get parts, very fair priced and very professional.

I had ask how to get the top off., it was simple ,take 3 screws off the bottom angle bracket .and slide top back about 2" then lift.then remove the front panels. '

Removed Top, then front and drum. Parts easy to access once drum is out. Recommend reading up on drum replacement. Would appear that all repairs will require taking it out.

First I just replaced the ignitor on a hunch, (disassembly was easy once I saw the video) I also examined the high limit thermostadt and found it was tripped, so I reset the button. the dryer fired up, but soon the thermo tripped again. I found that I could reach it with my arm placed in the inspection port,( about a 4 inch diameter pop out) make sure you unplug first, find the button near the ignitor, and pop it in. the high limit thermo was only holding a few seconds, so I decided to replace it, and did a "shot-gun" approach, replacing all thermos and thermisters at once, only about 35 bucks delivered...BTW, PartSelect shipped them to me at the speed of light.....one day ! Ireplaced all thermos and did and extra scrulpoulous cleaning of the vent. NOTE: it is completely possible that ahe only problem was a reduced vent capacity cmbined with summer heat leading to tripping the high limit thermo....however the thermo was tripping waaaay too easil in my opinion. Anyway, I celebrated doing 10 loads of piled up laundry, and basking in the glory of my wife's admiration for saving a $1000. appliance replacement. "how did you know how to do this honey?" "yoir so smart" (i did'nt tell her about the PartSelect video)

Could not fix original part. Ordered new lint screen and place it the dryer. No tools needed.

You will need a helper. Dismantle the Dryer: Remove the screws that hold the top cover, front control panel, front door and front panel. Release the V-Belt under the drum. Remove the Drum. Removed and replace the 2 Front roller assemblies - these were completely worn. Replaced the 2 rear rollers (did not replace the rear roller axels as these were more difficult to remove and they were in good shape) and the V-Belt while I had the whole thing open. Use a shop vac and cleaned up the whole unit. It is so nice and quiet now.

Simply removed the old filter and put in the new one. I was impressed with the sales person when I ordered the filter by phone. The online site didn't have a photo of it - just a description and price. She reassured me that I was ordering the correct item--she was very friendly. And the price was reasonable.

Seemed to be shutting off on the safety thermostat so I replaced them all. Works.

Removed the heating element, tested it, purchased a new element and installed.

After replacing the wires and the heat thermostat I realze that I needed to replace the thermostat ntc and the thermostat to blower located under door was burnt during fire. I removed front panel,front facing and tumbler to reach thermostat inter wall. It was easy after fixing to other area prior. I thought it was very easy and didn't cosume much time. I'm a women and it was easy to fix.

Not knowing whether it was the pulley, tensioner, or drum roller I had previously pulled the dryer apart and noticed one roller shaft was rusty for some reason. When the part came in (which was quite fast)I disassembled the dryer to the point that I could remove the left rear drum roller. Replaced the roller and reassembled the dryer (to my surprise without any extra screws or parts left). Fairly easy job, just time consuming.

I first took the top off, then the front control panel, unplugged the wires from panel (very easy), took the front panel off, the rum comes out very easy, be sure to look at the way the belt goes back on the pulley. I didn't and it took me a while to figure it out. All goes back together very easy.

removed the top of the dryer first by removing screws in the back and pulling the top back and up. Removed the control panel, followed by the door. The front panel and top brace were then removed. The belt was disengaged by pulling the tensioner idler and working the belt off the motor pulley. The drum was lifted out and set aside with the other parts. Holding the motor shaft with vice-grip pliers, and turning the nut on the blower wheel (left-hand thread!)removed the blower wheel. The motor is held by snap-on retainers and easily removed and swapped. Installation is reverse of disassembly. While in there, cleaned out the lint gathered everywhere. Also constructed a heat shield out of aluminum flashing and foil tape to cover the foil and foam tape between the burner assembly and sheet metal side. The foam had actually burned at some point in the past and the flashing should act as a better heat shield. A relatively easy repair, but should not have been necessary in a 7 year old dryer.