81022 LG Dryer - Instructions

Ordered a new one and installed it in a matter of seconds.
Not difficult!

Repair was easy, but the part does not come with directions. It is pretty self explanatory if you are used to taking things apart and fixing them. Otherwise there are YouTube videos you can pull up. Dryer runs like it is new again though and it was way cheaper than buying a new dryer.

Followed the instruction on video.was great after three parts now is OK .we have heat.still cheaper than having it service.

Exchange

Called LG on the phone and they gave the button presses for diagnostics, which then gave the HST code, saying the Humidity sensor was bad.
The part was described as the Humidity sensor module. Actually it's just the wire leads for the sensor which must be electronic and only accessible by disassembling the dryer. There were descriptions about cleaning the wires, perhaps because some people use dryer sheets which cause a buildup on the wires and prevent them from doing their job. I use wool balls and have no buildup on my wires and replacing them did not fix the sensor, because the module accessible inside the dryer is not the moisture sensor, but only the wire leads.

Entered dryer from rear exhaust port. Removed 2 screws and 2 clip on wires. A little awkward of process but superior method over disassembly of drum and main parts.

Unscrew the screw, remove old part, place in new part, replace screw and you are done.

There’s all sorts of videos on it I watched. It was actually very simple

watched the video on line then did the repair, very easy to replace

First of all, I watched the videos provided by this site. I am not a professional appliance technician.

My dryer is mounted on top of my LG washer.
I ordered appliance moving leg pads. And I ordered a small but effective jack to raise up both units to insert pads under the feet.
Now I could slide the stacking unit away from the wall.

I set out my drill, Phillips head bits, pliers, a socket set, a small crescent wrench, and my phone with videos.
I also used a short ladder to get up to the top of the dryer.
Having the dryer mounted on top of the washer was actually perfect for working from the front of the dryer cabinet.
Watch out for very sharp edges. You can wear gloves. But I found gloves to be an impediment to feeling the parts.

My replacement parts:
1) four drum support rollers with shafts. I replaced the roller and shafts together. The new rollers would not fit on the old shafts.
2) drive belt
3) two moisture sensors. Located on the lint filter housing.

Here is how it went:

I spent six hours in one day to disassemble, vacuum, reinstall parts, and reassemble. My dryer is a steam unit, so the control panel electronics are on the right side rather than on the front panel as in the video I watched. In order to replace the drum rollers and their mounting shafts I just needed to pull the drum rear mounting bracket forward just enough to get the small crescent wrench on the nut behind the roller and my socket wrench on the top of the roller shaft. And off they came.

I tested the dryer with a load of damp bath towels. The motor ran but the drum did not turn. It was then that I realized that I had the drum drive belt on with the wrong side facing the drum. One side of the drive belt is smooth. And the opposite side has parallel grooves. The parallel grooves side needs to contact both the drum as well as the motor pulley. The grooves face away from the tensioner pulley.

So, the next day I spent 90 minutes partially disassembling the dryer enough to get to the drum belt once again. I pulled out the drum again to wrap the drive belt over it in the correct orientation. It is not easy to see the motor drive pulley or the belt tensioner pulley. I did it by feel and watching the videos again. I hooked up the drive belt mostly by feel this time. And I got it done. Now the drier runs very quietly. By the way. No need to remove anything on the back of the dryer.

Pretty satisfying overall.

Viewed YouTube video form parts select to take dryer apart. Very easy to do if you just follow instructions in the video. Nothing too hard to do. Of note the 4 pack roller assembly is a whole unit, so you’ll have to replace the stem unit the old rollers use and not just replace the roller wheels like in the video. That is a different part number from LG. The front 2 are pretty straight forward to unbolt and replace. The back 2, especially one on the left is tighter clearance even with a wrench. If you’re able to pull whole dryer out and take back off, it’s an easier to get the one on the back left.
Also replaced belt just because i had it open, I replaced thermistor previously after getting a Te5 code about a year ago so that helped in taking it apart.
Would recommended doing it all since you’ll have it open.
Once replaced, everything ran again.

Removed the top, the control panel and the door. The heater assembly came out thru the front, without having to remove the drum. Easy replacement

Simple replacement

Removed cover replaced bulb

An appliance repairman determined the problem which was that it needed new pulleys and thankfully PartSelect carried them. He installed them in an hour and my dryer runs fine now.